background image

4

Non-Pump Model

Pump Model

Location of washer

Check location where washer will be installed. Make sure you have everything
necessary for correct installation.
Proper installation is your responsibility.

Do not place or store your washer below 0

°

C (32

°

F) to avoid any damage from freezing.

Install the washer on the horizontal solid floor.

Drain system

Never forget to install drain hose before operating your washer.
The packing box is opened, there are a drain hose.

INSTALLATION INSTRUCTIONS

 Connect the drain hose to the drain outlet at the back side of the washer.

Drain hose

Drain Outlet

Drain hose

If the washer is installed on an unsuitable floor, it could
make considerable noise, vibrate and cause a malfunction.
If washer is not level, adjust the front leg(A) up or down for
horizontal setting.

Earthed electrical outlet(B) is required with 20cm of

bottom back of washer cabinet.

Hot and cold water faucets (C) must be within 1m of the

upper back of the washer cabinet and provide water
pressure 29kPa ~ 784kPa (0.3kgf/cm  ~ 8kgf/cm  ).

2

2

C

UP

DOWN

B

A

NOTES

 The opening must not be obstructed by carpeting when the washing machine is 

installed on a carpeted floor.

Summary of Contents for DWF-450


















Reviews: