background image

CP-520

V

 Service Manual 

 

23

·   5 PWM (6-bits) outputs for analogue control functions 
·   Remote Control Pre-processor (RCP) 
·   Universal Asynchronous Receiver Transmitter (UART) 

Data Capture 

·   Text memory up to 10 pages 
·   Inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle 
Page Table (SPT) 
·   Data Capture for US Closed Caption 
·   Data Capture for 525/625 line WST, VPS (PDC system A) and Wide Screen Signalling (WSS) 
bit decoding 
·   Automatic selection between 525 WST/625 WST 
·   Automatic selection between 625 WST/VPS on line 16 of VBI 
·   Real-time capture and decoding for WST Teletext in Hardware, to enable optimized m-
processor throughput 
·   Automatic detection of FASTEXT transmission 
·   Real-time packet 26 engine in Hardware for processing accented, G2 and G3 characters 
·   Signal quality detector for video and WST/VPS data types 
·   Comprehensive teletext language coverage 
·   Vertical Blanking Interval (VBI) data capture of WST data 

Display 

·   Teletext and Enhanced OSD modes 
·   Features of level 1.5 WST and US Close Caption 
·   50Hz/60Hz display timing modes 
·   Two page operation for 16:9 screens 
·   Serial and Parallel Display Attributes 
·   Single/Double/Quadruple Width and Height for characters 
·   Smoothing capability of both Double Size, Double Width & Double Height characters 
·   Scrolling of display region 
·   Variable flash rate controlled by software 
·   Soft colours using CLUT with 4096 colour palette 
·   Globally selectable scan lines per row (9/10/13/16/) and character matrix [12x9, 12x10, 12x13, 
12x16, 16x18, (VxH)] 
·   Fringing (Shadow) selectable from N-S-E-W direction 
·   Fringe colour selectable 
·   Contrast reduction of defined area 
·   Cursor 
·   Special Graphics Characters with two planes, allowing four colours per character 
·   64 software redefinable On-Screen display characters 
·   4 WST Character sets (G0/G2) in single device (e.g. Latin, Cyrillic, Greek, Arabic) 
·   G1 Mosaic graphics, Limited G3 Line drawing characters 
·   WST Character sets and Closed Caption Character set in single device 
·   SVM for Text 
 
 
 
 
 

4.2 

LA42032

 STEREO AUDIO AMPLIFIER  

The 

LA42032

 is a dual-channel audio power amplifier with an output power of 2 x 

5

 W at an 8 

 load and a 

9

 V supply. 

Summary of Contents for DTX-21B4




























































Reviews: