background image

1 - 1

The CB650M-BX motherboard integrates the latest advances in pro c e s s o r,
m e m o r y, and I/O technologies into a Micro ATX form factor(244x205mm) that
combines performance, flexibility, and easy of use into high integrated capable
of meeting a variety of price/performance levels.

The CB650M-BX motherboard supports Intel Pentium II/III processor or
C e l e ron processor based on the Intel 440BX AGPsets(82443BX and 82371EB).
The CB650M-BX motherboard supports not only a 66MHz host but also a
100MHz host bus. So Intel Pentium II/III 350~450MHz processor and
Pentium II/III(Katmai) processor with a 100MHz host bus can be supported
for higher performance level. Two standard 168-pin DIMM Sockets with
memory size up to 256MB support Synchronous DRAM memory.

The Intel 82371EB PCI-to-ISA/IDE Xcelerator(PIIX4E) provides an integrated
Bus Master IDE controller and Ultra DMA/33 with high performance IDE
interfaces for up to four devices.

In addition, the CB650M-BX comes with an AGP(Accelerated Graphics Port)
bus slot, a faster than the current 33MHz PCI bus. The AGP bus provides a
d i rect connection between graphics subsystem and system memory.

1. Introduction

1. Introduction

Chapter 1.

Overview

CB650M-BX Mother Board

There is the danger of an explosion if the battery is incorrectly replaced.
Replace the battery with the same or equivalent type recommended
by the manufacturer. Discard used batteries according to the battery
manufacturer's instructions.

Caution :

CB650M-BX(1,2¿Â)  00.5.12 2:8 PM  

‰¿Ã¡ˆ1-1

Summary of Contents for CB650M-BX





























Reviews: