background image

10

Locate the 3 ¼” X 10 duct mounting flange included 

2. 

with the unit. Attach it to the open exhaust hole using 

the two (2) screws removed in step 1, with the flange 

facing outward.

Locate the vent cover included with the unit. Also locate 

3. 

the supplied foam tape. Peel the backing off the tape 

and attach it to the right and left flanges on the inside 

of the vent cover.
Remove and retain the three (3) wing nuts from the top 

4. 

retainer bracket on the front of the unit. Remove the 

bracket.
Slide the bottom flange of the vent cover into the bot-

5. 

tom retainer bracket with the wiring diagram facing out.
Cover the opening on the front of the unit by pushing 

6. 

the vent cover against it.
Make sure that the foam tape on the cover creates a 

7. 

good seal on the right and left sides of the opening. 

IMPORTANT:

 To prevent interference with the internal 

moving parts, make sure the cover is properly centered 

over the opening.
Reinstall the top retainer bracket over the top of the 

8. 

vent cover flange. Secure it in place with the three (3) 

wing nuts removed in step 4.

Parts List

Product literature

• 

Vent cover

• 

Anchoring legs

• 

2 wood screws, #14 x 2 1/2 (PN 83047)

• 

3 wire nuts

• 

2 sheet metal screws, #10 x 1/2 (PN 83022)

• 

3 ¼” X 10 duct mounting flange

• 

2 keps nuts, 1/4-20 (PN 83049)

• 

2 flat washers, 1/4-20 (PN 83203)

• 

Insulation foam

• 

Installation Preparation

 wARNING

If the electrical service does not meet the 

• 

Electrical 

Specifications

 on page 4, do not proceed with the 

installation. Call a licensed electrician to install an 

electrical circuit that meets the specifications.
Install the vent only in a vertical orientation. Do not 

• 

mount the vent on a slant or angle.
Do not enlarge or modify the exhaust knock outs or 

• 

cut an exhaust hole in a location on the chassis other 

than those shown. Doing so may cause an increase 

in noise and decrease performance.

Loosely attach the anchoring legs to the studs on the 

• 

left and right sides of the raised vent using the provided 

keps nuts and washers.

Installation Preparation for Raised Vent with 

ILHSF or REMP Series Blower:

NOTE: 

For units using the CABP3 cabinet blower, skip to 

Installing the Vent in the Cutout

 on the next page.

Remove and retain the two (2) screws on the cover 

1. 

plate over the exhaust that will be used (bottom or 

side). Discard the cover plate that was removed, but 

leave the two other cover plates in place.

Installation Instructions

Bottom 

cover

Exhaust Cover Removal (bottom shown)

Exhaust flange

Exhaust Flange Installation (bottom shown)

Adjustable

anchor legs

Front of 

raised vent

Top retainer 

bracket

Bottom retainer 

bracket

Vent cover

Flange

Attach 

foam to 

right/left 

flanges

Vent Cover Installation

Summary of Contents for RV30





















Reviews: