background image

3

2

36" (914mm) Recommended

30" (762mm) Min.

25"

(635mm)

30 1/16"

(764mm)10"

(254mm)

14"

(356mm)

Hood

30" (762mm)

Min.

6" (152mm) Min.

to combustible side

walls above the range

(both sides)

13"

(330mm)

Max.

1

10"

(254mm)

Top of 

finished

counter

Vertical

combustible

surface

18" (457mm)

Min.

Overall Cabinet Dimension and Clearance to Combustible Surfaces

Downdraft ERV30 with Slide-In, Self-Rimming Installation using 3” Side Panels (Model No. AESP03), Backguard Removed.

(RSD, RSE and MRE Models Only)

Top View

Slide-In, Self-Rimming Installation using 3” Side Panels (Model No. AESP03), Backguard Removed. (All Models)

Top View

Overall Dimensions

RSD30 Overall Dimensions (Dual Fuel)

Isometric View

RSE30/MRE30 Overall Dimensions (All Electric)

Isometric View

(RSE Shown)

Utilities may be located:

1.  In the lower left corner of the adjacent right 

cabinet. (Recommended)

2.  Alternate location, in the lower right corner 

behind the range. (Note: Some building 

departments do not permit concealing gas 

valves behind appliances.)

Contact your local building department to verify 

compliance with local code interpretation.

1/4" (6mm)

Min. flat ledge

28 11/16" (729mm)

11/16"

(17mm)

29 5/8" (752mm)

Rear wall

25"

(635mm)

Adjust for backsplash

thickness

13/16" to 4 1/4" 

(21 - 108mm)

Backsplash

Vertical

non-combustible

surface rear wall

27 13/16"

(706mm)

29 1/4" (743mm)

13/32" (10mm)

30 1/16" (764mm)

Countertop overhangs cabinet

6" (152mm) Min.

to combustible side

walls above the range

(both sides)

27 7/8" (708mm)

Adjust for backsplash

over 3/4" thick

from 13/16" to 3 13/16" 

(21 - 97mm)

Backsplash

thicker than

3/4" (19mm)

1/4" (6mm)

Min. flat ledge

Vertical

non-combustible

surface rear wall

2 13/16"

(71mm)

Summary of Contents for Preference RSD30









Reviews: