background image

Locate the chimney mounting bracket and position it 

against the ceiling as shown. Center it on the vertical 

center line drawn on the wall.

Mark the ceiling in two places through the holes in the 

top of the bracket. Remove the bracket from the ceiling.
Drill 5/16” holes through the two spots marked on the 

ceiling.
Insert the two of the provided wall anchors into the 

holes on the ceiling.
Place the chimney mounting bracket against the ceiling 

and attach it using two included 1 1/2” screws.

I

nsTall

 b

lower

 m

ounTIng

 

b

raCkeT

Find the mounting bracket template in the shipping 

box. Put the template against the wall and line up the 

horizontal line drawn on the wall with the horizontal line 

on the template.
Line up the vertical line drawn on the wall with the 

center line on the template. Iron out all creases and 

folds and tape the template to the wall using tape that 

will not damage the wall finish. 
Using a sharp object, mark the wall through the 

template at the center of the three blower mounting 

bracket hole positions (near the top) and the position of 

the two “L” brackets, near the bottom.
Remove the template.

4.

5.

6.

7.

8.

1.

2.

3.

4.

I

nsTallaTIon

 I

nsTruCTIons

 WARNING

Do not install the range hood unless the electrical 

service provided meets the range hood specifications.
Observe all governing codes and ordinances during 

planning and installation. Contact your local building 

department for further information.
A qualified technician must complete the installation 

of this built-in appliance. The owner is responsible to 

make sure the hood is properly installed.
To avoid an electric shock hazard and property 

damage, locate electric wires and water pipes and 

avoid drilling in the vicinity.

I

nsTall

 

The

 e

leCTrICal

 

C

onneCTIon

The electrical connection box must be:

Connected to a 120VAC, 60Hz dedicated, grounded, 

circuit protected by a 15 amp circuit breaker or time 

delay fuse.
Located a minimum of 17 inches above the underside 

of the range hood.
Located a maximum of three inches to the right or left 

of the central line of the range hood as you face the 

wall.

I

nsTall

 

The

 C

hImney

 m

ounTIng

 

b

raCkeT

Determine the vertical center line for the range hood. 

The center line for the hood is usually the same as the 

center line of the range or cooktop. 
Using a pencil, mark the vertical center line on the wall 

from where the bottom of hood will be located to where 

the top of the chimney will be located.
Draw a horizontal line 9 inches long at 90° to the 

vertical center line where the bottom of the hood will be 

located. The minimum allowable distance is 30” above 

the cooktop.

1.

2.

3.

ANCHOR

CHIMNEY

MOUNTING 

BRACKET

 WARNING

The electrical service to the range hood should be  

installed only by a licensed electrician.

Summary of Contents for Preference PHW301

















Reviews: