background image

I

nsTallaTIon

 C

heCklIsT

 WARNING

To ensure a safe and proper installation, the following 

checklist should be completed by the installer to 

ensure that no part of the installation has been 

overlooked.
Proper installation is the responsibility of the 

homeowner. The importance of proper installation of 

your Dacor

 

®

 range hood cannot be overemphasized.

Is the blower assembly mounting bracket properly 

attached to the wall according to the instructions on 

page 6?
Is the blower assembly tightly secured to the mounting 

bracket with the machine screws (see page 8)? 
Is the duct work completely installed? Are all joints 

attached with sheet metal screws and wrapped with 

duct tape (see pages 5 and 7)?
Is the range hood wired and grounded according to 

these instructions and in accordance with all applicable 

electrical codes (see pages 5 and 9)?
Is the tempered glass hood attached to the blower 

assembly as specified in this manual (see page 10)?
Are the filters properly installed according to the use 

and care manual?
Has proper operation been verified?
Have any problems been noted on the warranty card 

(see the use and care manual)? Has the warranty card 

been filled out completely and mailed?


I

nsTallaTIon

 I

nsTruCTIons

V

erIfy

 p

roper

 o

peraTIon

Turn on power at the junction or fuse box.
If the control panel is not lit, turn on the main power 

switch located next to the light fixture on the underside 

of the hood.
Touch the light key. Verify that all the lights come on. 
Touch the light key again to turn the lights off.
Touch the blower 

“+”

 key once and release. Verify that 

one light is showing on the blower speed indicator and 

that the blower is on at low speed.
Touch and release the blower 

“+”

 repeatedly, three 

times. Verify that with each touch of the key the number 

of lights on the blower speed indicator increases and 

that the blower speed increases.
Touch and hold the blower 

“-”

 key until the blower 

turns off.

If the hood fails to operate properly:

Verify that power is supplied to the hood.
Check the electrical connections to ensure that the 

installation has been completed correctly.
Repeat the above test.
If the appliance still does not work, contact an 

authorized Dacor

 

®

 service company at (800) 772-7778. 

Do not attempt to repair the appliance yourself. Dacor

 

®

 

is not responsible for service required to correct a faulty 

installation.

1.
2.

3.
4.
5.

6.

7.



Summary of Contents for Preference PHW301

















Reviews: