Dacor MHTW36, Installation Instructions Manual

Page: 4 / 8

3
Removing Anti-Grease Filter
wARNING:
TO REDUCE ThE RISK OF FIRE,
ELECTRIC ShOCK, OR INJURY
TO PERSONS, OBSERVE ThE
FOLLOwING:
1. Before making electrical
connections to power supply,
the electrical box must be
secured in place as indicated
below.
Before installing the appliance, fix the electrical box
as indicated below:
1. Remove the central screw.
Removing Central Screw
2. Lift the electrical plant box.
Lifting Electrical Plant Box
Power Supply Connection
For connection to the power supply refer to the
following:
BLACK = L line
WHITE = N neutral
GREEN/YELLOW = G ground
A double-pole switch properly rated must be
installed to provide the range hood power supply
disconnection.
Connecting Power Supply
Refer above for recommended
maximum straight lengths of duct to
provide adequate performance. Refer
above for recommended sheet metal
elbows, transitions, and wall cap
equivalent straight lengths.
NOTE:
The In Line Blower must be
located within 60 equivalent feet
of the hood canopy system.
Model
Number
Duct
Size
Maximum Equivalent Straight Lengths
Internal ILB8 REMP3 ILB8 & REMP3
MHTW36
8” Round 60’ 140’ 140’ -
10” Round 50’ 100’ 100’ -
3 1/4” x 10” 50’ 100’ 100’ -
Recommended Maximum Straight Lengths
3 1/4" x 10" 90û Elbow 3 1/4" x 10" 45û Elbow 3 1/4" x 10" Wall Cap 3 1/4" x 10"
90û Flat Elbow
Transistion
3 1/4" x 10" to Round
45û Elbow - Round Duct 90û Transistion
3 1/4" x 10" to 8"/10” Round
90û Elbow - Round Duct
15 Feet 7 Feet 2 Feet 20 Feet
8" Diameter - 4 Feet
10" Diameter - 4 Feet
8" Diameter - 3 Feet
10" Diameter - 2 Feet
25 Feet 8" Diameter - 7 Feet
10" Diameter - 5 Feet
Recommended sheet metal elbows, transition, and wall cap equivalent straight lengths
Electrical Power Supply
Requirements
NOTES:
1. If the power supply
requirements shown do
not agree with those listed
on the product data plate,
provide a power source per
the information found on the
product data plate.
2. If the electrical service
provided does not meet the
product specification, or
does not conform to the NEC
or local standards, do not
proceed with the installation.
Call a licensed electrician to
correct the electrical service
before proceeding.
3. It is the owner’s responsibility
to ensure that electrical
installation of this appliance
is performed by a qualified
electrician. The electrical
installation must comply
Electrical Supply Requirements
120VAC, 60 Hz, 15A Dedicated Circuit
Total Connected Load 1.4kW (8A)
The correct voltage, frequency, and amperage
must be supplied to the appliance from a
separate, grounded, circuit that is protected by a
properly sized circuit breaker or time delay fuse.
Refer to the data plate located on the blower
housing, inside the filter area, and/or to Table
below.
with the National Electric
Code ANSI/NFPA 70-1990 (or
to latest revision) and local
codes and ordinances.
4. Failure to disconnect electric
power may result in electrical
shock or fire hazard.
If a connection ductwork composed of two parts
is used, the upper part must be placed outside
the lower part. Do not connect the range hood
exhaust duct air to the same duct air used to
exhaust hot air or fumes from other appliances
other than electrical. Before proceeding with the
assembly operations, remove the anti-grease
filter(s) so that the unit is easier to handle.