Dacor Epicure ER36DSCH Installation Instructions Manual Download Page 18

Installation Instructions

Final Installation

Peel the protective coating off of the range, including the 

door.
Adjust the legs to the desired height.
Carefully slide the range into position in the cut-out. The rear 

anti-tip leg should engage the anti-tip bracket.

Re-installing the Oven Door(s)

 WARNING

To avoid personal injury or damage to the door from to it falling 

off its hinges:

Make sure that the notch on the bottom of each hinge rests 

on top of the lower lip of each hinge receptacle before 

attempting to open the oven door.

Rotate the hinge locks toward the front of the range 

immediately after installation of the door. 

Grasp the oven door on opposite sides and hold it at a 15° 

angle from the front of the oven. Slide the hinges into the 

hinge openings, resting the bottom of the hinge arms on the 

hinge receptacles. Continue to hold the door at a 15° angle 

with one hand while pushing in on each of the bottom corners 

of the door. Push until the notch on the bottom of each hinge 

slips over the lower lip of each hinge receptacle.
Lower the door to the fully opened position.
Rotate the two hinge locks toward the oven. 
Slowly and carefully open and close the door completely to 

ensure that it is properly installed. 
Remove any packaging from inside the oven(s).

1.

2.
3.

1.

2.
3.
4.

5.

Installing the Burner Knobs

 CAUTION

Installing the range knobs in the wrong position may result 

in damage to the griddle included with the range. The knobs 

for the center burners are marked with the maximum griddle 

settings.

NOTE:

 When installing the knobs, 

align the “D-shaped” opening on 

the back of the knob with the end 

of the valve shaft. Carefully push 

the knob on until it stops.
There are two (2) different types 

of knobs supplied with the range. 

The knobs for the center burners 

have the words “

MAX GRIDDLE”

 

on them.  

Put the knobs with the words 

MAX GRIDDLE”

 on them 

onto the inner (center burner) valve shafts. 

Put the remaining knobs on the outer valve shafts. 

Notch on bottom 

of hinge

Lower lip of 

hinge receptacle

Door Installation

Icons on Center Burner Knobs

Icons on Outer Burner Knobs

Summary of Contents for Epicure ER36DSCH

























Reviews: