background image

5

Product Dimensions

Side View:

 

ƒ

The depth from the front of the top grille to the back of the 
refrigerator cabinet is 25

 

³⁄

8

” (64.5 cm).

 

ƒ

 The power cord is 84” (213.3 cm) long.

 

ƒ

Height dimensions are shown with leveling legs extended ¹⁄

8

”  

(3.2 mm) below the rollers.

* When the leveling legs are fully extended to 1¼” (3.2 cm) below 

the rollers, add 1¹⁄

8

” (2.9 cm) to the height dimensions.

Top View:

Model

Width A

DYF42BIWS

41” (104.1 cm)

DYF48BIWS

47” (119.4 cm)

Installation Requirements

Front View:

 

ƒ

The width dimensions were measured from trim edge to trim 
edge.

 

ƒ

The height dimensions are shown with leveling legs extended 

¹⁄

8

”  

(3.2 mm) below the rollers.

Model

Width B (Trim edge to trim edge)

DYF42BIWS

42¼” (107.3 cm)

DYF48BIWS

48¼” (122.6 cm)

* When the leveling legs are fully extended to 1¼” (3.2 cm) below 

the rollers, add 1¹⁄

8

” (2.9 cm) to the height dimensions.

*3¹⁄

2

” (8.9 cm)

23¹⁄

2

” 

(59.7 cm)

25³⁄

8

” 

(64.5 cm)

*83³⁄

8

” 

(211.8 cm)

84” (213.4 cm) 

Power cord

25³⁄

8

” 

(64.5 cm)

A

(see following chart)

*83³⁄

8

” 

(211.8 cm)

Summary of Contents for DYF42BIWS



















Reviews: