background image

Electrical and grounding safety

WARNING

To reduce risk of fire, electric shock, personal injury, or death, observe these precautions:

Plug into a grounded, 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter or extension cord.

Do not use a damaged power plug, cord,

or loose power outlet.

Do not modify the plug, cord, or

 

outlet.

Do not put a fuse in a neutral or ground circuit.

Use a dedicated 120-volt, 60-Hz, 15-amp, AC, fused electrical circuit. A time-delay fuse

or circuit breaker is recommended. Plug only the cooktop into this circuit.

Do not connect the ground wire to plastic plumbing lines, gas lines, or hot-water pipes.

This cooktop must be grounded. In case of malfunction or breakdown, grounding

provides the current a safe path.

If unsure your electrical outlet is properly grounded, have a licensed electrician check it.

If codes allow a separate ground wire, have a qualified electrician determine its path.

Electrical service to the cooktop must conform to local codes, or in the absence of

local codes, to the National Electrical code/NFPA No. 70 – Latest Revision (for the U.S.)

or the Canadian Electrical Code CSA C22.1 or Latest Revisions.

The owner shall ensure the cooktop is provided proper electrical service.

Location safety

WARNING

To reduce risk of fire, electric shock, personal injury, or death, observe these precautions:

The cooktop is for indoor household use

 

only. Do not install the cooktop outside

 

or

anywhere that it will be exposed to

 

weather, water, wind, or strong drafts.

On windows near the cooktop, do not

 

hang paper blinds or long curtains that

 

could

 

be

blown over the cooktop.

The cooktop must be installed within easy reach of a grounded, 3-prong outlet.

For proper ventilation, the cooktop needs sufficient space below

all around the

 

chassis.

Vents in the chassis exhaust heat and fumes so the cooktop can operate

 

properly.

W

all coverings around the cooktop 

must be able to 

withstand heat up to 194 °F

 

(90 °C).

Do not store items above the cooktop. If cabinet storage above the cooktop is

 

ne

eded

,

allow 

at least 

30 in. (76.2 cm) between the cooking surface

 

and the cabinet

 bottom

.

8

 English

Summary of Contents for DTG36M955F





































Reviews: