background image

Verifying burner function

After the cooktop is fully installed, connected, assembled, and plugged in, verify burner 

function. Perform this procedure for each burner in turn.

To turn on a cooktop burner

1.

Push in, and turn a burner control

knob to the "Lite" position (flame icon).

A "click-click-click...” indicates the

electronic ignition system functions.

The burner ignites in about 4 seconds ,

after air is purged from the gas line.)

2.

Turn the knob to the desired setting.

(The “clicking” stops; the flame height

changes from HI to LO as you turn the

knob counterclockwise.)

NOTE

If the burner does not light within 4 seconds, turn the knob off and wait one minute

 

before trying again.

Checking flame quality

All burner flames must be visually checked to assess their quality.

CAUTION

If you want measure the flame, take care to avoid burn injuries.

2

3

1

1.

Soft blue flames

—Normal for natural

gas operation.

2.

Yellow tips on outer cones

—Normal for

LP gas operation.

3.

Yellow flames

—Abnormal for any gas

operation; call for service.

NOTE

Normal burner flames look like Ex. 1 or 2. 

If the flame looks like Ex. 3, do not use the 

cooktop, and call for service.

2

6

 English

Summary of Contents for DTG36M955F





































Reviews: