DAB e.sybox Series, Manual

Page: 27 / 54

ENGLISH
GB
83
7.1.9 - Multi-pump system 7.1.9 - Multi-pump system
Displays the system status when in the presence of a multi-pump instal
-
Displays the system status when in the presence of a multi-pump instal
-
lation. If communication is not present, an icon depicting communication lation. If communication is not present, an icon depicting communication
absent or interrupted is displayed. If there are several devices connected absent or interrupted is displayed. If there are several devices connected
to one another, an icon is shown for each of them. The icon has the symbol to one another, an icon is shown for each of them. The icon has the symbol
of a pump under which are characters indicating the pump status. of a pump under which are characters indicating the pump status.
Depending on the operating status it will display as in Table 11. Depending on the operating status it will display as in Table 11.
System display
Status Icon
Status information under the
icon
Motor running Symbol of pump turning speed in three figures
Motor stopped
Symbol of static pump
SB
Device faulty Symbol of static pump
F
If the device is configured as reserve the icon depicting the pump is dark in If the device is configured as reserve the icon depicting the pump is dark in
colour, the display remains similar to Table 8 with the exception that, if the colour, the display remains similar to Table 8 with the exception that, if the
motor is stopped, it shows F instead of SB. motor is stopped, it shows F instead of SB.
7.1.10 - Output flow meter 7.1.10 - Output flow meter
The page shows two flow meters. The first shows the total output flow The page shows two flow meters. The first shows the total output flow
delivered by the machine. The second shows a partial count and can be delivered by the machine. The second shows a partial count and can be
reset by the user. reset by the user.
The partial count can be reset from this page, by holding down the “ - “ The partial count can be reset from this page, by holding down the “ - “
button for 2 sec. button for 2 sec.
7.1.11 - VE: Version display 7.1.11 - VE: Version display
Hardware and software version with which the appliance is equipped. Hardware and software version with which the appliance is equipped.
Hardware and softwa 5.9.0 and later, the following also applies: Hardware and softwa 5.9.0 and later, the following also applies:
on this page after the prefix S: the last 5 figures of the single serial number on this page after the prefix S: the last 5 figures of the single serial number
attributed for connectivity are showed. The whole serial number can be attributed for connectivity are showed. The whole serial number can be
viewed by pressing the “+” key. viewed by pressing the “+” key.
Table 11: View of the multi-pump system
7.1.5 - PO: Absorbed power display 7.1.5 - PO: Absorbed power display
Power absorbed by the electropump in [kW]. Power absorbed by the electropump in [kW].
A flashing round symbol may appear under the symbol of the measured A flashing round symbol may appear under the symbol of the measured
power PO. This symbol indicates the pre-alarm for exceeding the allowed power PO. This symbol indicates the pre-alarm for exceeding the allowed
maximum power maximum power
7.1.6 - C1: Phase current display 7.1.6 - C1: Phase current display
Motor phase current in [A]. Motor phase current in [A].
A flashing round symbol may appear under the symbol of the phase cur
-
A flashing round symbol may appear under the symbol of the phase cur
-
rent C1. This symbol indicates the pre-alarm for exceeding the allowed rent C1. This symbol indicates the pre-alarm for exceeding the allowed
maximum current. If it flashes at regular intervals it means that the motor maximum current. If it flashes at regular intervals it means that the motor
overload protection is about to trip and it will very probably go into protec
-
overload protection is about to trip and it will very probably go into protec
-
tion status tion status
7.1.7 - Operating hours and number of starts 7.1.7 - Operating hours and number of starts
Indicates on three lines the hours that the device has been powered up, Indicates on three lines the hours that the device has been powered up,
the pump working hours and the number of starts of the motor. the pump working hours and the number of starts of the motor.
7.1.8 - PI: Power histogram 7.1.8 - PI: Power histogram
A histogram of the power delivered is displayed on 5 vertical bars. The A histogram of the power delivered is displayed on 5 vertical bars. The
histogram indicates how long the pump has been on at a given power histogram indicates how long the pump has been on at a given power
level. On the horizontal axis are the bars at the various power levels; on level. On the horizontal axis are the bars at the various power levels; on
the vertical axis, the time for which the pump has been on at the specific the vertical axis, the time for which the pump has been on at the specific
power level (% of the time with respect to the total). power level (% of the time with respect to the total).
Figura 16: Power histogram display