background image

LIMITED WARRANTY – VIEWSHARE PRODUCTS

Milestone AV technologies LLc warrants its Da-Lite branded Viewshare products to the original purchaser only, to be free from defects 
in materials and workmanship in accordance with the following warranty term:

A period of five (5) years for the Advantage screen and related components; and 

A period of three (3) years for the Viewshare camera and related components.

the foregoing warranty will commence upon the date of purchase by the original purchaser and is expressly contingent upon the 
products being properly operated according to Da-Lite’s instructions and not damaged due to improper handling or treatment after 
shipment from the factory.

this warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered 
with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. 
returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, 
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment. to 
protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY.

 Any implied warranties of fitness for use, 

or merchantability, that may be mandated by statute or rule of law are limited to the above warranty period. this warranty gives you 
specific legal rights, and you may also have other rights, which vary from state-to-state. 

TO THE MAXIMUM EXTENT PERMITTED BY 

APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF 
EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our sales Partners at Po Box 137, 
Warsaw, In 46581-0137, (574) 267-8101, (800) 622-3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS 
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

keep your sales receipt to prove the date of purchase and your original ownership.

24953

A Milestone AV Technologies Brand

3100 north Detroit street 
Warsaw, Indiana 46582 
P: 574.267.8101 or 800.622.3737 
f: 574.267.7804 or 877.325.4832 
E: [email protected] 
www.da-lite.com

DL–0158 (Rev.1) 09.13 
© 2013 Milestone AV Technologies LLC. Printed in U.S.A.

Summary of Contents for Viewshare Advantage Electrol













Reviews: