background image

2

Carefully unpack screen and remove outer wrapping from case.

Remove the black tape and rubber bands from the slat bar after the case has been installed.

The Large Cosmopolitan® Electrol® comes with brackets to allow for wall mount or ceiling mount installations. Procedures for each 

method are as follows:

Wall Mount

1.  The wall mount bracket should be fastened to wall studs or 

some reinforcement within the wall. Concrete or brick walls 
require special fasteners and anchors.

2.  The wall bracket has holes spaced at 16" and 24" to align with 

most wall studs.

3.  The bracket must be level and plumb.

4.  Keep in mind you will need at least 2-3/4" between the ceiling 

and the top of the wall mount bracket to be able to position 
the case on the bracket.

5.  Mount the screen case on the wall bracket as shown in  

figure 1. Be sure the case is fully seated on the bracket. 
Tighten the stop screws against the wall bracket.

Ceiling Mount

1.  Be sure the ceiling has adequate reinforcement to attach the 

screen brackets.

2.  Attach the ceiling brackets to the wall mount bracket using 

the supplied 5/16" x 3/4" bolts, washers and nuts.

3.  Position the ceiling bracket assembly on the ceiling and 

attach with 5/16" bolts (not supplied). The bolts should be 
long enough to pass through the drywall or ceiling tile and 
penetrate at least 1-1/2" into the reinforcement in the ceiling.

4.  Mount the screen on the wall bracket as shown in figure 2. Be 

sure the case is fully seated on the bracket. Tighten the stop 
screws against the wall bracket.

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1.  Read and understand all instructions before using.

2.  To reduce the risk of electric shock, do not disassemble this 

appliance. Contact an authorized service dealer when repair 
work is required. Incorrect reassembly can cause electric 
shock when the appliance is used subsequently.

3.  The use of an accessory attachment not recommended by 

the manufacturer may cause a risk of fire, electric shock, or 
injury to persons.

Installation 

1 1/8"

Case Hook

Viewing Surface 
(Audience Side)

Figure 2

Figure 1

Viewing Surface 
(Audience Side)

Case Hook

Wall Mount  

Bracket

Stop Screw

Ceiling Mount 

Bracket

5/16 x 3/4" Bolt 

Nut and Lock 

Washer

Wall Mount 

Bracket

Stop Screw

2

"

Summary of Contents for Large Cosmopolitan Electrol













Reviews: