background image

TROUBLESHOOTING

SYMPTOM

3.   Door will 

not

 open.

 

 

4.   Door does 

not

 close.

 

5. 

“Down”

 limit switch incorrect.

6.  Noise.

 

 NOTE: Screen will operate with a low-
pitched hum.

7.  Coasting.

8.   Roller displaced from mounting 

bracket.

9.  Fabric hangs crooked.

10.  Door closes before screen is all the 

way up.

11.  Door opens but screen does not 

operate.

CAUSE

(a)   Hinge is bound or has a foreign 

substance on it which does not allow 

it to open by gravity.

(b)  No power.

(a)   Open door limit switch.

(b)  No power from screen motor.

(c)  Unit not calibrated. 

(a)   

“Down”

 limit switch out of 

 

adjustment.

(a)  Buzzing noise.

(b)   Gear noise.

(a)   Defective brake.

(a)  Pin end slipped out of nylon bearing.

(a)  Screen not installed properly.

(b)   Fabric is damaged.

(a)  Screen 

“up”

 limit out of adjustment.

(a)  Loose wire.

SOLUTION

(a)   Check installation to free door. Clear 

any foreign substance; i.e., paint or 

plaster from hinge.

(b)  See above.

(a)   Replace switch.

(b)  Replace screen motor.

(c)  Recalibrate per instructions on page 

3.

(a)   See installation instructions.

(a)   Adjust door limit switch (too far 

down).

(b)   Replace motor assembly.

(a)   Replace motor assembly.

(a)   Realign pin end bracket.

(a)   Check for level and plumb.

(b)   Replace fabric.

(a)  Adjust 

“up”

 limit (call factory for 

instructions).

(a)  Check all wiring and connections.

9

Summary of Contents for ADVANTAGE DELUXE ELECTROL













Reviews: