manualshive.com logo in svg

D.W. Fearn VT-7, Operating Instructions Manual

Share
Download
D.W. Fearn VT-7 Operating Instructions Manual Download Page 21

D.W. FEARN

VT-7 Compression Amplifier

26

Second stage

The output of the first stage is coupled to the grid of the second stage through a polypropy-
lene capacitor. This stage operates as a Class A voltage amplifier with a gain of approximate-
ly 20. 

Output Stage

The output stage operates as a cathode follower, followed by a custom output transformer
built for D.W. Fearn by Jensen Transformers, Inc. The output impedance is 115 ohms.

Meter and Meter Amplifier

Two-stage IC operational amplifiers are used to isolate the VU meters from the VT-7 outputs.
An output sample is derived from the primary of the output transformer. The VU meter
amplifiers are constructed on the printed circuit board that also contains the Link/Link HPF
circuitry. It is mounted above the main chassis. The meter calibrations set with a 20-turn
trimmer potentiometer. Reference level (0 VU) can be set from -20 to over +20dBm.

The meter can monitor gain reduction in the “GR” position. The meter is driven by a preci-
sion circuit that provides exact tracking with the actual amount of gain reduction. The meter
“0” adjustments are on the PWM boards.

The level indictor is a custom true VU meter conforming to ASA Standard C16.5-1954.

Power Supplies

Primary power from the AC mains is connected to the VT-7 through a standard IEC power
input connector with an integrated power switch. The Power switch energizes all five power
supplies. A mains voltage selector switch on the back panel allows the primary voltage of the
VT-7 to be easily changed in the field.

A fuse protects the VT-7. The Pilot lamp is a type 1819 bulb, operated far below its rated volt-
age of 28. The life of the bulb is lengthened, and the light output is more compatible with
other modern studio equipment. The power transformer is a toroidal unit custom-made for
the VT-7 and has primary taps for 100, 120, or 220-240 volt operation.

Filament Supply

The power transformer output is rectified by a bridge rectifier and filtered before being reg-
ulated, The output of this supply is 12 volts. 

Low-voltage Supplies

This supply pr15, -15, and +5 volts for the solid-state circuitry in the Pulse Width
Modulator.

B+ Supply

Eight separate regulated voltages are required for the plates of the VT-7. The B+ is filtered
with long-life, low-leakage, computer-grade filter capacitors before being regulated and exten-
sively bypassed and decoupled. The negative side of the supply is grounded.

Summary of Contents for VT-7

























Reviews:

No comments

Brands by name

Popular brands

Load more brands