background image

18 

IMPORTANT SAFETY NOTES 

• 

Before  training,  your  dog  should  be  examined  by  a 
veterinarian  to  assure  that  your  dog  is  in  good 
health. 

  

• 

Never  leave  your  dog  unattended  with  the  unit 
on.

  Since no electronic device is perfect, there is a 

very  slight  possibility  that  your  dog  may  receive  an 
unintentional electric stimulation. 

  

• 

Your 

RH  300

 training collar is a very valuable tool if 

used  correctly.    It  is  extremely  important  that  you 
completely understand all the functions of the collar 
and how to properly train with it before placing it on 
your dog. 

  

• 

The  contacts  (electrodes)  on  this  collar  are  made 
with  high  grade  stainless  steel  to  help  prevent  any 
chemical or allergic reactions with your dog’s skin.

 

  

• 

To  prevent  neck  irritations,  the  collar  should 
never  be  worn  for  more  than  12  hours  a  day.  

Changing the collar location on the dog’s neck daily 
will  also  help  prevent  irritations.    It  is  important  to 
keep  the  collar  clean.    Clean  the  electrodes 
regularly with a mild anti-bacterial soap. 

  

• 

If an irritation is found, carefully wash the dog’s neck 
with  soap  and  water  and  then  wipe  the  area  with  
Hydrogen  peroxide.    Dry  thoroughly  and  apply  an  
antibiotic ointment. 

Summary of Contents for RedHead RH 300





















Reviews: