background image

1

D-Link DWP-1010 Quick Install Guide

EN

G

LI

SH

Important Information

This product should ONLY be installed by 

an experienced installer who is familiar with 

local building and safety codes and, where 

applicable, is licensed by the appropriate 

authorities. Failure to employ an experienced 

installer may render the D-Link product 

warranty void and may also expose the end 

user or the service provider to legal and 

financial liabilities. D-Link and its resellers 

or distributors expressly disclaim any and all 

liabilities for injury, damage, or violation of 

regulations due to the improper installation 

of outdoor units or antennas.

Quick Install Guide

This installation guide provides basic 

instructions for installing the DWP-1010 

outdoor CPE on your network. For 

additional information about how to use 

the DWP-1010, please see the datasheet 

and user manual from the D-Link support 

website.

Minimum System 

Requirements

 

-

Compatible iOS or Android device

 

-

iOS® version 12.0 or Android™ 20.0, or 

newer

 

-

A home router, switch, or Wi-Fi access 

point

Package Contents

 

-

DWP-1010 5G/LTE Outdoor CPE

1

 

-

Quick Installation Guide

 

-

Pole Mount Kit

 

-

Stainless Clamp x 2

 

-

Wall Mount Kit

 

-

Screw Anchor (M6x25 mm)

 

-

Screws (M3.5x16 mm) 

 

-

PoE Injector (48V power supply)

2

 

-

AC Power Cable 

 

 

-

RJ-45 Ethernet Cable (15 m) for connection 

between the DWP-1010 and the PoE 

Injector

 

-

RJ-45 Ethernet Cable (1 m) for connection 

between the PoE Injector and an indoor 

CPE (a home router, witch, etc.) 

 

-

Warranty Card

 

-

GPL Sheet

If any of the above items are missing, please 

contact your reseller.

1

   This product is an outdoor device and the  

power is always on; no power standby 

mode is available.

2

  

Using a power supply with a different 

voltage rating of PoE Injector than the one 

included with the DWP-1010 may cause 

damage and void the warranty for this 

product.

Physical Installation

STEP 1: Install SIM card.

SIM

PoE

RESET

WIFI

Remove the 4 screws on the bottom of the 

DWP-1010 to remove the protective base.       

               

SIM

PoE

RESET

WIFI

Remove the six screws from the water-resistant 

component. Observe the orientation label on 

the device to insert the SIM card with the right 

orientation.

Summary of Contents for DWP-1010

Page 1: ... through the basic installation process for your new D Link Outdoor CPE DWP 1010 Documentation also available on the D Link Website Quick Installation Guide 5G LTE Outdoor CPE Quick Installation Guide Building Networks for People ...

Page 2: ...ice iOS version 12 0 or Android 20 0 or newer A home router switch or Wi Fi access point Package Contents DWP 1010 5G LTE Outdoor CPE1 Quick Installation Guide Pole Mount Kit Stainless Clamp x 2 Wall Mount Kit Screw Anchor M6x25 mm Screws M3 5x16 mm PoE Injector 48V power supply 2 AC Power Cable RJ 45 Ethernet Cable 15 m for connection between the DWP 1010 and the PoE Injector RJ 45 Ethernet Cable...

Page 3: ...e with the four M3x4 mm screws Skip this step if wall mount will be used Mounting Mount the DWP 1010 to a Pole Use two stainless clamps to attach the DWP 1010 to a pole Do not tighten firmly until the site survey is completed Refer to Connect the DWP 1010 to Your Network and Configuration To adjust the installation loosen slightly and slide Mount the DWP 1010 to a Wall Before fixing the DWP 1010 o...

Page 4: ...ides using site survey you can obtain general signal strength information with the aid of LED indicators on the side of the DWP 1010 5G 4G 3G LED Connection Type Off No Signal Solid Green LTE 3G Solid Blue 5G Note Once the site survey is completed the DWP 1010 sWi Fi function will be disabled You will need to remove the bottom assembly of the DWP 1010 to reactivate theWi Fi function using theWi Fi...

Reviews: