manualshive.com logo in svg

D-Link DWM-312, User Manual, Page: 47 / 96

Share
Download
D-Link DWM-312 User Manual Download Page 47

43

D-Link DWM-312 User Manual

Section 4 - Configuration

Tick this box to enable MAC Filtering.

Check the box to allow wireless and wired clients with 

C

 selected 

to connect to this device. You can also select to 

allow 

or 

deny 

connections from unspecified MAC addresses.

MAC FILTERING RULES

This identifies the rule.

Specify the MAC address of the computer to be filtered.

If this box is ticked, the rule will follow the connection control 

setting specified in MAC filtering settings specified above.

Click 

Apply

 to save your settings, or 

Refresh

 to revert to your 

previous settings.

MAC Address 

Control:

Connection 

Control:

ID:

MAC Address:

 

C:

The 

MAC (Media Access Controller) Address Filter

 option is used to control network access based on the MAC address of the network adapter. 

A MAC address is a unique ID assigned by the manufacturer of the network adapter. This feature can be configured to ALLOW or DENY network/

Internet access.

MAC Address Filter

Summary of Contents for DWM-312

































































































Reviews:

No comments