D-Link DVG-7062S User Manual Download Page 57 | Manualshive

Page: 57 / 71

background image

55

System Information

This page shows that the status of VoIP Gateway. There are Port Status, Server Registration Status, WAN
Port Information, LAN Port Information and Hardware.

Port Status: It includes if each port registers to Proxy successfully, the lasted dialed number,
how many calls each port had since the system is start, etc.

Server Registration Status: It shows the registration status of DDNS, Phone Book Manager,
STUN and UPnP.

WAN Port Information: It shows IP address, subnet mask, default gateway and DNS server.
If you use PPPoE to obtain IP, you can know if the IP is obtained through this.

LAN Port Information: It shows LAN port IP, subnet mask, and the status of DHCP server.

Hardware: It shows the hardware platform.

«
...
55
56
57
58
59
...
»

Summary of Contents for DVG-7062S








































































Reviews:

No comments

Related manuals for DVG-7062S

Brand: Pace Pages: 2

Brand: UrsaLeo Pages: 5

NIOT-E-TPI51-EN-RE

Brand: hilscher Pages: 258

Brand: Top Global Pages: 75

Brand: Zipato Pages: 36

Brand: Pathport Pages: 3

Brand: Ruckus Wireless Pages: 2

Brand: WELLTECH Pages: 2

Brand: Alpha Technologies Pages: 25

Brand: Argent Data Systems Pages: 34

Brand: Sony Pages: 70

Brand: Sony Pages: 76

lpnGate LoRaWAN

Brand: LPN Plant Pages: 20

Brand: ICP DAS USA Pages: 48

Brand: Planet Networking & Communication Pages: 73

Brand: Discovery Telecom Pages: 46

Brand: Wildix Pages: 5

Brand: Ness Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands