![background image](http://html.mh-extra.com/html/d-link/dsl-g604t/dsl-g604t_user-manual_74534053.webp)
DSL-G604T Wireless ADSL Router Manual
Username &
Password
Type the Username and Password used to verify the identity of your account.
Typically, the Username is an account number assigned by your ISP. See your ISP
for further information.
Connection Type
Choose between
PPPoE LLC, PPPoA LLC
or
PPPoE VC-Mux,
depending on the
instructions of your ISP.
MTU
The Maximum Transmission Unit (
MTU
) is a link layer restriction on the maximum
number of bytes of data in a single transmission. The default size is 1400 bytes per
packet. NAT improves network security in effect by hiding the private network behind
one global and visible IP address.
MRU
The Maximum Receive Unit (
MRU
) field indicates the maximum number of bytes
that can be received by the Router. This MRU’s default size is 1492 bytes per
packet. Upon initial negotiation with your ISP, the router will tell the ISP that the
amount entered here is the largest packet that can be accepted by the router.
Default Route
Click the corresponding radio button if you wish to enable or disable the Default
Route. The Default Route is used for outgoing packets, which have an unresolved IP
address. If the router is unable to match the destination address on a received
packet with a destination address in the routing table, the router uses the default
route.
NAT
NAT improves network security in effect by hiding the private network behind one
global and visible IP address. NAT address mapping can also be used to link two IP
domains via a LAN-to-LAN connection. Use the pull-down menu to Enable or Disable
NAT on the Router.
Firewall
The
Firewall
allows the Router to enforce policies to protect against certain kinds of
attacks. To enable the firewall on the Router, use the pull-down menu and select
Enabled
.
IP Control
This field allows the user to control the WAN IP address of the router. There are
three choices for the user:
Dynamic IP
– Select this option if you wish to have an IP address automatically
assigned to the router.
Unnumbered IP
– Select this option if your ISP has assigned a block of IP
addresses for use.
Static IP
– Select this option if you know the IP address assigned to the router. After
selecting this option, the user must enter the known Static IP address in the following
field. A Static IP address is used whenever a known static IP is assigned.
Static IP
This field states the Static IP Address of the Router can only be configured when
Static IP is chosen in the previous field.
Click
Apply
to implement the PPPoE settings for the DSL-G604T.
Bridge Mode
Selecting this option in the WAN Settings will change your screen to look like the one seen below.
Bridge
Mode
is for users who have software on their computer or other network device to accept the
connection from your ISP. The
Connection Type
setting is
selected by using the pull-down menu.
The two choices available to the user here are
1483 Bridged IP LLC
and
1483 Bridged IP Vc-Mux,
and this correct choice should be provided to you by your ISP.
53
Summary of Contents for DSL-G604T
