D-Link DSL-2544N User Manual Download

Page: 60 / 68

Section 3 – Web Configuration

D-Link DSL-2544N User Manual

IP Address

Choose

MAINTENANCE

Access Controls

Remote Access Control

. The

page shown as the figure appears on the right.

In this page, you can configure the IP address for access control list (ACL). If ACL

is enabled, only devices with the specified IP addresses can access the device.

Note:

If you enable the ACL, ensure that IP address of the host is in the ACL list.

To add an IP address to the IP list, click

Add

. The page shown in the figure

appears on the right.

Click

Apply

to save the settings, and then choose

Enable Access Control Mode

enable ACL.

Diagnostics

DSL Test

Choose

MAINTENANCE

Diagnostic

DSL Test

, the page shown as the figure

appears on the right. In this page, you can test your DSL connection.

This page is used to test the connection to your local network, the connection to

your DSL service provider, and the connection to your Internet service provider.

Click

Rerun Diagnostics Test

to run diagnostics.

Summary of Contents for DSL-2544N





































































Search results

Summary of Contents for DSL-2544N

Reviews:

Related manuals for DSL-2544N

Brands by name

Popular brands

D-Link DSL-2544N, User Manual

Search results

Summary of Contents for DSL-2544N

Reviews:

Related manuals for DSL-2544N

Brands by name

Popular brands