D-Link DSL-2544N User Manual Download

Page: 38 / 68

Section 3 – Web Configuration

D-Link DSL-2544N User Manual

Choose

ADVANCED

DMZ

to go to the following page.

Click

Apply

to save the settings.

SAMBA

enables the workstation in the network to share the USB flash disk connected to the router.

Select

ADVANCED

SAMBA

. The page shown in the figure appears on the right.

The following table describes the parameters of this page.

Field

Description

Enable SAMBA

Select the check box to enable the samba

service

Workgroup

Enter the name of your local area network (LAN).

Netbios Name

Enter your netbios name which is an identifier

used by netbios services running on a computer.

New SMB password

Enter your samba password for user root.

Retype new SMB

password

Reconfirm your samba password here.

Enable USB Storage Select the check box to support USB storage.
Enable Anonymous

Access

Select the check box to allow anonymous users

access.

Summary of Contents for DSL-2544N





































































Search results

Summary of Contents for DSL-2544N

Reviews:

Related manuals for DSL-2544N

Brands by name

Popular brands

D-Link DSL-2544N, User Manual

Search results

Summary of Contents for DSL-2544N

Reviews:

Related manuals for DSL-2544N

Brands by name

Popular brands