manualshive.com logo in svg

D-Link DIR Series, User Manual

Share
Download
D-Link DIR Series User Manual Download Page 55

51

D-Link DIR-600 User Manual

Section 4 - Security

Configure WPA-Personal (PSK)

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish 

wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to 

the added overhead.

1. 

Log into the web-based configuration by opening a web browser 

and entering the IP address of the router (192.168.0.1). Click on

 

Setup 

and then click Wireless Settings on the left side and then 

click Manual Wireless Network Setup.

2. Next to 

Security Mode

, select 

WPA/WPA2

.

3. Next to 

Cypher Type

, select 

AUTO(TKIP/AES)

 

TKIP

, or 

AES

. If you 

have wireless clients that use both types, use 

AUTO(TKIP/AES)

.

4. Next to 

Pre-Shared Key

, enter a key (passphrase). The key is entered as a pass-phrase in ASCII format at both ends 

of the wireless connection. The pass-phrase must be between 8-63 characters. 

5. Click 

Save Settings

 to save your settings. If you are configuring the router with a wireless adapter, you will lose 

connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router.

Summary of Contents for DIR Series











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands