manualshive.com logo in svg

D-Link DIR Series, User Manual

Share
Download
D-Link DIR Series User Manual Download Page 20

16

D-Link DIR-600 User Manual

Section 3 - Configuration

Dynamic IP Address (DHCP)

Select 

Dynamic IP (DHCP)

 to obtain IP Address information 

automatically from your ISP. Select this option if your ISP does 

not give you any IP numbers to use. This option is commonly 

used for Cable modem services.

The Host Name is optional but may be required by some ISPs. 

Enter the Primary DNS server IP address assigned by your ISP.

Maximum Transmission Unit - you may need to change the 

MTU for optimal performance with your specific ISP. 1500 is 

the default MTU.

The default MAC Address is set to the Internet port’s physical 

interface  MAC  address  on  the  Broadband  Router.  It  is  not 

recommended that you change the default MAC address unless required by your ISP.  You can use the 

Clone Your PC’s 

MAC Address

 button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

My Internet 

Connection:

Host Name:

MTU:

MAC Address:

DNS Addresses:

Summary of Contents for DIR Series











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands