manualshive.com logo in svg

D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter, User Manual

Share
Download
D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter User Manual Download Page 9

D-Link DGE-560T User Manual

6

Hardware Installation

1.  Shut down the computer and unplug the power cord.

2.  Remove the chassis cover. If you are installing a network adapter in a tower computer, we recommend to put the computer 

on its side in order to be able to apply the correct force to insert the adapter into the PCI Express slot. 

3.  Locate an empty PCI Express slot on the motherboard.

4.  Insert the network adapter into the PCI Express slot and push it down vertically into the slot until it is firmly seated.

5.  Install the bracket screw to secure the network adapter to the computer chassis.

6.  Replace the computer chassis cover. Reconnect the power and switch the computer power on. If the BIOS section of your 

computer’s boot program is plug-and-play compliant, then at power-up the BIOS will automatically configure any newly 
installed adapter. Skip to page 16 to verify your installation.

Summary of Contents for DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network Adapter






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands