D-Link DCS-5020L User Manual Download Page 43

Page: 43 / 76

D-Link DCS-5222L User Manual

Section 4 - Configuration

Note:

Video Profile 3 is always set to MJPEG as the Encode Type to ensure that at least one of the Video Profiles are viewable by non-IE browsers.

Video Profile 4 is for mobile devices only, and always uses H.264 as the Encode Type.

Note:

Higher frame size, frame rate and bit rates will give you better video quality, but they will also require more network bandwidth. For best

viewing results on a mobile phone, we suggest setting the frame rate to 5 fps and the bit rate to 20 Kbps.

After making any changes, click the

Save Settings

button to save your changes, or click the

Don’t Save Settings

button to discard your changes.

Day/Night

Mode:

Audio Setup:

Allows you to control the IR LEDs on the front of the camera. Note that when this option is enabled, live feed video will be in black

and white, and ICR filter will be activated.

Allows you to enable or disable and adjust the volume level of the speaker and microphone. If you select speaker, you must

attach external speakers to the audio port on the camera.

Summary of Contents for DCS-5020L













































































Search results

Summary of Contents for DCS-5020L

Reviews:

Related manuals for DCS-5020L

Brands by name

Popular brands

D-Link DCS-5020L, User Manual

Search results

Summary of Contents for DCS-5020L

Reviews:

Related manuals for DCS-5020L

Brands by name

Popular brands