background image

FCC Interference Statement

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions,   may cause harmful interference to

radio   communications.         However,     there   is   no   guarantee   that

interference will not occur in a particular installation.  If this equipment

does cause harmful interference to radio or television reception,  which

can be determined by turning the equipment off and on,  the user is

encouraged to try to correct the interference by one of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and

(2)   This   device   must   accept   any   interference   received,   including

interference that may cause undesired operation.

 

FCC Caution: Any changes or modifications not expressly approved by

the party responsible for compliance could void the user's authority to

operate this equipment.

 

This transmitter must not be  co-located or  operating in  conjunction

with any other antenna or transmitter.

Warning

Do not dispose of electrical appliances as unsorted municipal waste,

use   separate   collection   facilities.   Contact   your   local   government   for

information   regarding   the   collection   systems   available.   If   electrical

appliances are disposed of in landfills or dumps, hazardous substances

can leak into the groundwater and get into the food chain, damaging

your health and well-being.

When replacing old appliances with new once, the retailer is legally

obligated to take back your old appliance for disposal at least for free

of charge.

13

Summary of Contents for DCH-Z110














Reviews: