D-Link AirPremier DWL-00AP Manual Download Page 83 | Manualshive

Page: 83 / 84

background image

83

Operating Voltage

• 48VDC +/- 0% for PoE

Radio and Modulation Type

For 80.b:

DSSS:

• DBPSK @ Mbps

• DQPSK @ Mbps

• CCK @ 5.5 and Mbps

For 80.g:

OFDM:

• BPSK @ 6 and 9Mbps

• QPSK @ and 8Mbps

• 6QAM @ 4 and 36Mbps

• 64QAM @ 48 and 54Mbps

DSSS:

• DBPSK @ Mbps

• DQPSK @ Mbps

• CCK @ 5.5 and Mbps

Transmit Output Power

For 80.b:

• 58mW (dBm)

• 79mW (9dBm)

• 40mW (6dBm)

• 0mW (0dBm)

• mW (0dBm)

For 80.g:

• 6mW (dBm)

• 63mW (8dBm)

• 30mW (5dBm)

• 0mW (dBm)

• mW (0dBm)

Receiver Sensitivity

For 80.b:

• Mbps: -9dBm

• Mbps: -90dBm

• 5.5Mbps: -88dBm

• Mbps: -85dBm

For 80.g:

• Mbps: -9dBm

• Mbps: -90dBm

• 5.5Mbps: -88dBm

• 6Mbps: -88dBm

• 9Mbps: -86dBm

• Mbps: -85dBm

• Mbps: -85dBm

• 8Mbps: -83dBm

• 4Mbps: -80dBm

• 36Mbps: -76dBm

• 48Mbps: -7dBm

• 54Mbps: -7dBm

LEDs

• Power

• LAN

• 80.b/g

Temperature

• Operating: 3ºF to 04ºF (0ºC to 40ºC)

• Storing: -40ºF to 49ºF (-40ºC to 65ºC)

Humidity

• Operating: 0%~90% (non-condensing)

• Storing: 5%~95% (non-condensing)

Certifications

• FCC

• CE

• UL

• Wi-Fi / WMM

Dimensions

• L = 0.93 inches (77.7mm)

• W = 6.0 inches (55mm)

• H = .77 inches (45mm)

Warranty

• Year

Technical Specifications

«
...
81
82
83
84
»

Summary of Contents for AirPremier DWL-00AP





















































































Reviews:

No comments

Related manuals for AirPremier DWL-00AP

Brand: Cambium Networks Pages: 5

Brand: Cambium Networks Pages: 44

Brand: Hirschmann Pages: 42

Brand: Ruckus Wireless Pages: 4

Brand: TP-Link Pages: 45

UniFi UAP-AC-LITE

Brand: Ubiquiti Pages: 28

Brand: Pakedge Pages: 6

Brand: TP-Link Pages: 2

Brand: Cellient Pages: 23

Brand: VXI Pages: 2

MiFi 500 LTE Mobile Hotspot

Brand: Novatel Pages: 9

Brand: Novatel Pages: 123

Brand: Novatel Pages: 108

Brand: Linksys Pages: 1122

Brand: Linksys Pages: 1334

Brand: Atlantis Land Pages: 83

WebShare 144 WN+

Brand: Atlantis Pages: 19

Brand: Datto Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands