D-Link AirPlus Xtreme G DI-824VUP User Manual Download Page 31 | Manualshive

Page: 31 / 157

background image

31

Home > VPN Settings > Dynamic VPN Tunnel

Using the Configuration Menu

Local Subnet

The subnet of the VPN gateway’s local network. It can be a
host, a partial subnet, or a whole subnet.

Local Netmask

The netmask of the VPN gateway’s local network.

Aggressive Mode

Enabling this mode will accelerate establishing the tunnel,
but the device will have less security.

Tunnel Name

Current tunnel name.

This feature works with a VPN software client so the DI-
824VUP does not need to know the IP address of the remote
clients.

Dynamic VPN

There are three parts that are necessary to setup the
configuration of IKE for the dedicated tunnel: basic setup, IKE
proposal setup, and IPSec proposal setup. Basic setup
includes the setting of following items: local subnet, local
netmask, remote subnet, remote netmask, remote gateway,
and pre-shared key. The tunnel name is derived from the
previous page of VPN setting. IKE proposal setup includes
the setting of a set of frequent-used IKE proposals and selecting
from the set of IKE proposals.

VPN Settings - IKE

«
...
29
30
31
32
33
...
»

Summary of Contents for AirPlus Xtreme G DI-824VUP






























































































































































Reviews:

No comments

Related manuals for AirPlus Xtreme G DI-824VUP

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: ZyXEL Communications Pages: 15

Brand: VT Miltope Pages: 32

Brand: versa Pages: 103

SOUNDFLOW i17 +

Brand: WEEPLUG Pages: 22

SpeedStream 2624

Brand: Siemens Pages: 2

Brand: Siemens Pages: 6

Brand: Siemens Pages: 28

GIGASET SE681 WIMAX

Brand: Siemens Pages: 72

Gigaset SX682 WiMAX

Brand: Siemens Pages: 74

SCALANCE W748-1

Brand: Siemens Pages: 68

SCALANCE W786-x

Brand: Siemens Pages: 68

SpeedStream SS2524

Brand: Siemens Pages: 90

SCALANCE W786-1PRO

Brand: Siemens Pages: 90

OZS164 SERIES WEB SERVER

Brand: Siemens Pages: 108

SCALANCE W786-xPRO

Brand: Siemens Pages: 250

SIMATIC NET SCALANCE W721-1

Brand: Siemens Pages: 256

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands