Master 3
Slave 1
Slave 2
The drive set is fully configured ex factory.The drives
must be reconfigured using SCS in the event of
changes to the ex-factory configuration
(e.g. when removing a drive from
existing set or integrating
a new drive).
If after mounting, the distance X is greater than
23 mm, null balance with software SCS is
neccesary. Closure Ranges will shift in relation
to new zero point.
Mount the drives whilst
under zero stress.
With that, an even
load distribution is
provided by all
the drive chains.
At vertical active pulling application (e.g. for a
skylight) the forces must be rearranged by software
SCS.
Mounting information
Slave 1
≥ 23 mm ?
X
English
99.823.67 2.6/03/16
CDC 200/350(-SBD)-BSY+
8/20
English
CDC 200/350 (-SBD)-BSY+
9/20
99.823.67 2.6/03/16
Visual inspection:
Only one master drive is allowed.
The master always has the last address of all the
drives; this can be found on a sticker attached to
the drive. Slaves are numbered downwards from
the master, so that in a group of three drives, for
example, the master is no. 3, with a slave 2 and
slave 1 drive. Please note that this only applies in
the ex-factory configuration. As soon as the drives
are reconfigured with SCS, the ex-factory
addressing no longer applies.
Wiring:
Is the group wired correctly?
Please refer to the connection diagrams in this
regard.
Adjustment of zero point:
Adjust the zero point.
Software SCS or the special magnet
MAG 502 is required.
Call D+H Service:
Drives must be configured.
Software SCS is required.
Troubleshooting
A CDC -BSY+ synchronous group can contain up to
8 drives, which communicate via bus. Each drive has
its own address, configurable with SCS.
The last drive of a synchronous group is the master,
which controls the other drives, the slaves.
Differences in forces between the drives of a group
are balanced by means of intelligent force and
position control. In the event that a drive
malfunctions, all the drives are automatically cut off.
Functional description
Maintenance and cleaning
Maintenance work is only allowed when the device is in
a de-energized condition! Inspection and maintenance
has to be carried out according to D+H maintenance
notes. Only original D+H spare parts may be used.
Repair is to be carried out exclusively by D+H.
Wipe away debris or contamination with a dry, soft
cloth.
Do not use cleaning agents or solvents.
Guarantee
You will get 2 years guarantee for all D+H products
from date of verified handing over of the system up to
maximal 3 years after date of delivery, when
mounting and starting has been carried out by an
authorized D+H-distributor.
D+H guarantee is expired, with connection of D+H
components with external systems or with mixing of
D+H products with parts of other manufacturers.
Electrical devices, accessories, batteries and packa-
ging should be sorted for environmental-friendly
recycling. Do not dispose electrical devices and
batteries into household waste!
Only for EC countries:
According the European Guideline 2012/19/EU for
waste electrical and electronic equipment and its
implementation into national right, electrcal devices
that are no longer usable must be collected separa-
tely and disposed of in an environmentally correct
manner.
Disposal
Declaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following directives:
2014/30/EU, 2014/35/EU
Technical file at:
D+H Mechatronic AG, D-22949 Ammersbek
Dirk Dingfelder
Maik Schmees
Member of the Board
Authorized signatory, Technical Director
24.02.2016
Minimum sash height/ -width
The details apply to a
non-rotational installation of the drive!
Standard chain:
Minimum size (mm) = Stroke (mm) x 3.9
Side bow chain -SBD:
Stroke
Minimum size (x)
150 mm = 300 mm
280 mm = 450 mm
350 mm = 550 mm
x
x
