Cyrus PSU-XR User Manual Download Page 8

6

Cyrus PSU-XR

User Instructions

1. 

Standby/Status indicator

Operation

Front panel controls

There are no user controls on the PSU-XR front panel. 

All functions including standby and configuration are 

controlled by the connected Cyrus product via the power 

interconnect cable.

Standby/Status indicator colour and brightness

The Standby/Status indicator brightness and colour settings 

will automatically be set to match the indicator brightness 

and colour settings on a connected Cyrus product.

Key to the front panel drawing

PSU-XR

1

Power control

Mains power

In regular use mains power can be left connected 

permanently. 

When unattended for a long period (holidays etc) mains 

power should be disconnected.

Standby/Status indication

When mains power is connected, the Standby/Status 

indicator will initially flash to show the firmware version 

(refer to the ‘Firmware’ section of this user guide for more 

information), then light red as standby is set.
When a connected product switches on the Standby/Status 

indicator will change to the colour of the connected Cyrus 

product. This confirms that power is now being supplied 

from the PSU-XR.
NOTE: If the PSU-XR remains in Standby then a firmware 

update may be required for the connected Cyrus product. 

Refer to the ‘Support’ pages of the Cyrus website www.

cyrusaudio.com to determine whether an update is 

required.

Auto Standby

There is no energy saving auto-standby setting for the 

PSU-XR as it will always set to the same power state as the 

Cyrus product it is connected to. 

If auto-standby is required it can be enabled at the 

connected product.

Summary of Contents for PSU-XR













Reviews: