Cyrus Pre-XR User Manual Download Page 27

Cyrus Pre-XR

User Instructions

25

Specifications

Power Supply

Voltage: ...........................................As plate on rear of unit

Power Consumption

Standby...................................................................... <0.5W
Maximum ..................................................................... 10W
EMC & Safety Compliance ................................................

CE

Enclosure

Dimensions (WxHxD) .............................. 215 x 75 x 365mm
Weight ......................................................................... 4.0kg
Material ....................................................... Die cast chassis

Analogue audio performance

Input Sensitivity ........................................................ 500mV
Input Impedance  ........................................................ 40kΩ
Frequency Response (-3dB) ......................... 0.1Hz, >500kHz
Signal to Noise Ratio (unWTD) ...................................108dB
THD+N, 1kHz .......................................................... <0.002%
Output voltage (unbalanced) ...........................................1V
Output voltage (balanced)................................................2V
Max output voltage (unbalanced) .................................2.5V
Max output voltage (balanced) ........................................5V
Output impedance (unbalanced) .................................. 47Ω
Output impedance (balanced) ...................................... 47Ω

Digital audio performance

Input voltage ...................................................500mV pk-pk
Input Impedance ........................................................... 75Ω
Sample rate range (SPDIF) .............................. 22.05k - 192k
Sample rate range (USB) ................................... 44.1k - 768k
Audio formats (SPDIF) ....................................... PCM stereo
Audio formats (USB) ...... DSD64, DSD128, DSD256, DSD512

DoP, PCM

S/N ratio (Pre-out, 0dB FS) .................................... >113dBA
THD (Pre-out, 0dB FS) ............................................. <0.001%

Cyrus reserves the right to change all specifications without notice. E &OE

Warranty

The warranty period is two years. No retailer or distributor 

may vary the terms of this warranty, which is personal to 

the original purchaser and is not transferable.
Please retain the sales receipt as proof of purchase.
Warranty claims must wherever possible be made through 

the retailer from whom the equipment was purchased.
This warranty excludes:

• 

Damage caused through neglect, accident, misuse, 

wear and tear, or through incorrect installation, 

adjustment or repair by unauthorised personnel. Any 

unauthorised servicing will result in loss of warranty.

• 

Liability for damage or loss occurring in transit to or 

from the purchaser.

• 

Consequential damage, loss or injury, arising from or in 

conjunction with this equipment. 

Equipment for attention under warranty should be 

consigned return carriage paid. If returned equipment is 

found to comply with the published specification, CYRUS 

reserves the right to raise a charge.
The above conditions do not affect your statutory rights as 

a consumer.

WEEE

This logo means that this product is not 

to be disposed of with your household 

waste. This product should be handed 

over to a designated collection point to be 

recycled. Your cooperation in the correct 

disposal of this product will contribute to 

the effective usage of natural resources. 

For more information on collection points, 

contact your local government for more 

information about recycling.

Cyrus Pre-XR english v1.2

Summary of Contents for Pre-XR





























Reviews: