Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 78 / 410

background image

14

Document # 001-20559 Rev. *D

Analog Output Drivers

7.2

Register Definitions

The following register is associated with the Analog Output Drivers. The register description has an associated register table
showing the bit structure of the register. The bits that are grayed out in the table below are reserved bits and are not detailed
in the register description that follows. Reserved bits should always be written with a value of ‘0’. Depending on the number of
analog columns your PSoC device has (see the Cols. column in the register table below), some bits may be reserved (refer to
the table titled

“PSoC Device Characteristics” on page 20

).

7.2.1

ABF_CR0 Register

The Analog Output Buffer Control Register 0 (ABF_CR0)
controls analog input muxes from Port 0 and the output buf-
fer amplifiers that drive column outputs to device pins.

For more information on bit 7, see the

Configuration chapter on page 241

Bit 7: ACol1MUX.

A mux selects the output of column 0

input mux or column 1 input mux. When set, this bit sets the
column 1 input to column 0 input mux output.

Bit 5: ABUF1EN.

Enables the analog output buffer for Ana-

log Column 1 (Pin P0[5]). A ‘0’ disables the analog output
buffer, a ‘1’ enables.

Bit 3: ABUF0EN.

Enables the analog output buffer for Ana-

log Column 0 (Pin P0[3]). (1 Column: AGND). A ‘0’ disables
the analog output buffer, a ‘1’ enables

Bit 1: Bypass.

Bypass mode connects the analog output

driver input directly to the output. When this bit is set, all
analog output drivers are in bypass mode. This is a high
impedance connection used primarily for measurement and
calibration of internal references. Use of this feature is not
recommended for customer designs.

Bit 0: PWR.

This bit is used to set the power level of the

analog output drivers. When this bit is set, all of the analog
output drivers are in a High Power mode.

For additional information, refer to the

ABF_CR0 register on

.

Add.

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

1,62h

ACol1Mux

ABUF1EN

ABUF0EN

Bypass

PWR

RW : 00

«
...
76
77
78
79
80
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

ETHERIOS ConnectCore 6

Brand: Digi Pages: 15

Brand: Vantron Pages: 68

Brand: Lex Computech Pages: 112

Brand: SBS Technologies Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands