Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 307 / 410

background image

Document # 001-20559 Rev. *D

243

Analog Input Configuration

20.2

Register Definitions

The following registers are associated with Analog Input Configuration and are listed in address order. Each register descrip-
tion has an associated register table showing the bit structure for that register. For a complete table of the analog input config-
uration registers, refer to the

“Summary Table of the Analog Registers” on page 217

.

Only certain bits are accessible to be read or written. The bits that are grayed out throughout this manual are reserved bits
and are not detailed in the register descriptions that follow. Reserved bits should always be written with a value of ‘0’.

20.2.1

AMX_IN Register

The Analog Input Select Register (AMX_IN) controls the
analog muxes that feed signals in from port pins into the
analog column.

Bits 3 to 0: ACIx[1:0].

For two column PSoC devices, the ACI1[1:0] and ACI0[1:0]
bits control the analog muxes that feed signals in from port
pins into the analog column.

The analog column can have up to eight port bits connected
to its muxed input. ACI1 and ACI0 are used to select among
even and odd pins. The AC1Mux bit field controls the bits for
those muxes and is located in the Analog Output Buffer
Control register (ABF_CR0). There are up to two additional
analog inputs that go directly into the Switched Capacitor
PSoC blocks.

For additional information, refer to the

AMX_IN register on

.

20.2.2

ABF_CR0 Register

The Analog Output Buffer Control Register 0 (ABF_CR0)
controls analog input muxes from Port 0 and the output buf-
fer amplifiers that drive column outputs to device pins.

Bit 7: ACol1MUX.

A mux selects the output of column 0 input mux or column 1
input mux. When set, this bit sets the column 1 input to col-
umn 0 input mux output.

Bit 5: ABUF1EN

Enables the analog output buffer for Analog Column 1 (Pin
P0[5]). A ‘0’ disables the analog output buffer, a ‘1’ enables.

Bit 3: ABUF0EN

Enables the analog output buffer for Analog Column 0 (Pin
P0[3]). (1 Column: AGND). A ‘0’ disables the analog output
buffer, a ‘1’ enables

Bit 1: Bypass.

Bypass mode connects the analog output driver input
directly to the output. When this bit is set, all analog output
drivers are in bypass mode. This is a high impedance con-
nection used primarily for measurement and calibration of
internal references. Use of this feature is not recommended
for customer designs.

Bit 0: PWR.

This bit is used to set the power level of the

analog output drivers. When this bit is set, all of the analog
output drivers are in a High Power mode.

For additional information, refer to the

ABF_CR0 register on

Add.

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,60h

ACI1[1:0]

ACI0[1:0]

RW : 00

Add.

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

1,62h

ACol1Mux

ABUF1EN

ABUF0EN

Bypass

PWR

RW : 00

«
...
305
306
307
308
309
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Brand: GIGAIPC Pages: 38

Brand: Octagon Pages: 118

Brand: Critical Link Pages: 4

Brand: Lex Pages: 78

Brand: Lex Pages: 91

Brand: Lex Pages: 100

Brand: BOSER Technology Pages: 52

gKINO-DMF Series

Brand: IEI Technology Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands