CYBLE-012011-00
CYBLE-012012-10
EZ-BLE™ PRoC™ Module
Cypress Semiconductor Corporation
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Document Number: 002-02521 Rev. *F
Revised April 25, 2017
EZ-BLE™ PRoC™ Module
General Description
The CYBLE-01201X-X0 is a Bluetooth
Low Energy (BLE)
wireless module solution. The CYBLE-01201X-X0 is a turnkey
solution and includes onboard crystal oscillators, trace antenna,
passive components, and the Cypress PRoC™ BLE. Refer to
the CYBL10X6X
for additional details on the capabil-
ities of the PRoC BLE device used on this module.
The CYBLE-01201X-X0 supports a number of peripheral
functions (ADC, timers, counters, PWM) and serial
communication protocols (I
2
C, UART, SPI) through its
programmable architecture. The CYBLE-01201X-X0 includes a
royalty-free BLE stack compatible with Bluetooth 4.1 and
provides up to 23 GPIOs in a 14.52 × 19.20 × 2.00 mm package.
The CYBLE-01201X-X0 is available in a fully certified and
qualified version (CYBLE-012011-00), and an uncertified version
(CYBLE-012012-10). The CYBLE-012012-10 does not include
an RF shield and is not certified by Bluetooth SIG or refulatory
agencies.
The CYBLE-01201X-X0 is a complete solution targeted at appli-
cations requiring cost optimized BLE wireless connectivity.
Module Description
■
Module size: 14.52 mm ×19.20 mm × 2.00 mm (with shield)
■
Castelated solder pad connections for ease-of-use
■
128-KB flash memory, 16-KB SRAM memory
■
Up to 23 GPIOs configurable as open drain high/low,
pull-up/pull-down, HI-Z analog, HI-Z digital, or strong output
■
Bluetooth 4.1 qualified single-mode module
❐
QDID:
(CYBLE-012011-00 only)
❐
Declaration ID:
(CYBLE-012011-00 only)
■
Certified to FCC, IC, MIC, KC, and CE regulations
■
Industrial temperature range: –40 °C to +85 °C
■
32-bit processor (0.9 DMIPS/MHz) with single-cycle 32-bit
multiply, operating at up to 48 MHz
■
Watchdog timer with dedicated internal low-speed oscillator
(ILO)
■
Two-pin SWD for programming
Power Consumption
■
TX output power: –18 dbm to +3 dbm
■
Received signal strength indicator (RSSI) with 1-dB resolution
■
TX current consumption of 15.6 mA (radio only, 0 dbm)
■
RX current consumption of 16.4 mA (radio only)
■
Low power mode support
❐
Deep Sleep: 1.3 µA with watch crystal oscillator (WCO) on
❐
Hibernate: 150 nA with SRAM retention
❐
Stop: 60 nA with GPIO (P2.2) or XRES wakeup
Functional Capabilities
■
Up to 22 capacitive sensors for buttons or sliders with
best-in-class signal-to-noise ratio (SNR) and liquid tolerance
■
12-bit, 1-Msps SAR ADC with internal reference,
sample-and-hold (S/H), and channel sequencer
■
Two serial communication blocks (SCBs) supporting I
2
C
(master/slave), SPI (master/slave), or UART
■
Four dedicated 16-bit timer, counter, or PWM blocks
(TCPWMs)
■
LCD drive supported on all GPIOs (common or segment)
■
Programmable low voltage detect (LVD) from 1.8 V to 4.5 V
■
I
2
S master interface
■
Bluetooth Low Energy protocol stack supporting generic
access profile (GAP) Central, Peripheral, Observer, or
Broadcaster roles
■
Switches between Central and Peripheral roles on-the-go
■
Standard Bluetooth Low Energy profiles and services for
interoperability
■
Custom profile and service for specific use cases
Benefits
The CYBLE-01201X-X0 module is provided as a turnkey
solution, including all necessary hardware required to use BLE
communication standards.
■
Proven hardware design ready to use
■
Cost optimized for applications without space constraint,
Footprint
❐
14.52 × 19.20 mm × 2.00 mm - CYBLE-012011-00
❐
14.52 × 19.20 mm × 1.55 mm - CYBLE-012012-10
■
Reprogrammable architecture
■
Fully certified module (CYBLE-012011-00) eliminates the time
needed for design, development and certification processes
■
Bluetooth SIG qualified with QDID and Declaration ID
(CYBLE-012011-00 Only)
■
Flexible communication protocol support
■
PSoC Creator
™
provides an easy-to-use integrated design
environment (IDE) to configure, develop, program, and test a
BLE application
