Cypress CY8C28 series Technical Reference Manual Download | Manualshive

Page: 49 / 571

background image

48

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

CPU Core (M8C)

2.7

Register Definitions

The following register is associated with the CPU Core (M8C). The register description has an associated register table show-
ing the bit structure. The bits that are grayed out in the table are reserved bits and are not detailed in the register description
that follows. Reserved bits should always be written with a value of ‘0’.

2.7.1

CPU_F Register

The M8C Flag Register (CPU_F) provides read access to
the M8C flags.

Bits 7 and 6: PgMode[1:0].

PgMode determines how the

CUR_PP, STK_PP, and IDX_PP registers are used in form-
ing effective RAM addresses for Direct Address mode and
Indexed Address mode operands. PgMode also determines
whether the stack page is determined by the STK_PP or
IDX_PP register.

Bit 4: XIO.

The I/O Bank Select bit, also known as the reg-

ister bank select bit, is used to select the register bank that
is active for a register read or write. This bit allows the PSoC
device to have 512 8-bit registers and therefore, can be
thought of as the ninth address bit for registers. The address
space accessed when the XIO bit is set to ‘0’ is called the

, while the address space accessed when the

XIO bit is set to ‘1’ is called the

configuration space

.

Bit 2: Carry.

The Carry flag bit is set or cleared in response

to the result of several instructions. It can also be manipu-
lated by the flag-logic opcodes (for example, OR F, 4). See

the

PSoC Designer Assembly Guide User Manual

for more

details.

Bit 1: Zero.

The Zero flag bit is set or cleared in response

to the result of several instructions. It can also be manipu-
lated by the flag-logic opcodes (for example, OR F, 2). See
the

PSoC Designer Assembly Guide User Manual

for more

details.

Bit 0: GIE.

The state of the Global Interrupt Enable bit

determines whether interrupts (by way of the interrupt
request (IRQ)) will be recognized by the M8C. This bit is set
or cleared by the user, using the flag-logic instructions (for
example, OR F, 1). GIE is also cleared automatically when
an interrupt is processed, after the flag byte has been stored
on the stack, preventing nested interrupts. If desired, the bit
can be set in an

interrupt service routine (ISR)

.

For GIE = 1, the M8C samples the IRQ input for each
instruction. For GIE = 0, the M8C ignores the IRQ.

For additional information, refer to the

CPU_F register on

.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

x,F7h

PgMode[1:0]

XIO

Carry

Zero

GIE

RL : 02h

LEGEND

L

The AND F, expr; OR F, expr; and XOR F, expr flag instructions can be used to modify this register.

x

An “x” before the comma in the address field indicates that this register can be read or written to no matter what bank is used.

«
...
47
48
49
50
51
...
»

Summary of Contents for CY8C28 series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CY8C28 series

Brand: Balboa Instruments Pages: 10

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 31

Brand: NAiS Pages: 199

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 179

Brand: Panasonic Pages: 23

Brand: 2M Technology Pages: 17

Brand: 2iB Pages: 5

Brand: Caen Pages: 20

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Brand: Galaxy Control Systems Pages: 5

Brand: Hach Pages: 36

Brand: Linear Technology Pages: 7

J1000 CIMR-JC series

Brand: YASKAWA Pages: 25

Brand: TDSi Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands