background image

Document Number: 001-07037 Rev. *D

Revised June 16, 2008

Page 30 of 30

QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung. All product and company names mentioned in this document
are the trademarks of their respective holders.

CY7C1411BV18, CY7C1426BV18

CY7C1413BV18, CY7C1415BV18

© Cypress Semiconductor Corporation, 2006-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. 

Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress. 

Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges. 

Use may be limited by and subject to the applicable Cypress software license agreement. 

Sales, Solutions, and Legal Information 

Worldwide Sales and Design Support

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at 

cypress.com/sales.

Products

PSoC

psoc.cypress.com

Clocks & Buffers

clocks.cypress.com

Wireless

wireless.cypress.com

Memories

memory.cypress.com

Image Sensors

image.cypress.com

PSoC Solutions

General

psoc.cypress.com/solutions

Low Power/Low Voltage

psoc.cypress.com/low-power

            

Precision Analog 

psoc.cypress.com/precision-analog

LCD Drive

psoc.cypress.com/lcd-drive

CAN 2.0b

psoc.cypress.com/can

USB

psoc.cypress.com/usb

Document History Page

Document Title: CY7C1411BV18/CY7C1426BV18/CY7C1413BV18/CY7C1415BV18, 36-Mbit QDR™-II SRAM 4-Word
Burst Architecture
Document Number: 001-07037

REV.

ECN NO.

SUBMISSION

DATE

ORIG. OF 

CHANGE

DESCRIPTION OF CHANGE

**

433267

See ECN

NXR

New Data Sheet

*A

462004

See ECN

NXR

Changed t

TH 

and t

TL 

from 40 ns to 20 ns, changed t

TMSS

, t

TDIS

, t

CS

, t

TMSH

, t

TDIH

t

CH 

from

 

10 ns to 5 ns and changed t

TDOV 

from 20 ns to 10 ns in TAP AC Switching 

Characteristics table 
Modified Power Up waveform

*B

850381

See ECN

VKN

Minor change: Moved datasheet to the web

*C

1523289

See ECN

VKN/AESA Converted from preliminary to final, Updated Logic Block diagram, Updated 

I

DD

/I

SB

 specs, Changed DLL minimum operating frequency from 80MHz to 

120MHz, Changed t

CYC

 max spec to 8.4ns, Modified footnotes 22 and 30

*D

2478647

See ECN

VKN/AESA Changed Ambient Temperature with Power Applied from “–10°C to +85°C” to 

“–55°C to +125°C” in the “Maximum Ratings “ on page 20, Updated Power-up 
sequence waveform and it’s description, Updated I

DD

/I

SB 

specs, Added footnote 

#21 related to I

DD

,

 

Changed JTAG ID [31:29] from 001 to 000.

[+] Feedback 

Summary of Contents for Perform CY7C1411BV18































Reviews: