manualshive.com logo in svg

CYP PUV-1630TTX, Operation Manual, Page: 32 / 44

Share
Download
CYP PUV-1630TTX Operation Manual Download Page 32

32

COMMAND

Description and Parameters

set automation event N1 cec delay N2 sec

Set the delay time that the specified Automation Event must 
continue to be true before sending the defined CEC command.

Available values for 

N1

: 

1 

[Power on] 

2 

[Out A source active] 

3 

[Out A source lost]

N2

 = 1 ~ 300 

[Delay in seconds]

get automation event N1 cec delay

Show the delay time for the specified Automation Event's CEC 
response.

Available values for 

N1

: 

1 

[Power on] 

2 

[Out A source active] 

3 

[Out A source lost]

set automation event N1 cec wait N2 sec

Set the length of time to wait after an Automation Event's CEC 
response has been activated before ANY other Automation Event 
can be detected.

Available values for 

N1

: 

1 

[Power on] 

2 

[Out A source active] 

3 

[Out A source lost]

N2

 = 1 ~ 300 

[Wait time in seconds]

Note: If both an RS-232 and CEC event is activated by the same 
Automation Event, the longer of the 2 wait times will be used.

Summary of Contents for PUV-1630TTX













































Reviews:

No comments