CYP CM-1391, Operation Manual

Page: 7 / 8

Video to DVI
Scaler Box
Operation Manual
CM-1391
(10). Installation
VCR, DVD, STB, DVHS
PC display Monitor,
Projectors
DVI
output
Video,
SVideo
DVI
Input
DVI Cable
VCR, DVD, STB, DVHS
CV
SV
a. Digital Out: Connect to your TV through digital DVI interface
b. Analog Out: Connect to your TV through VGA or component interface
in case your TV has no DVI input
Analog
HDTV output
VGA to YPbPr/3 RCA cable
VGA cable
Analog
PC output
DVI to
VGA
Adaptor
6
1. Power button and LED indicator:
Press the button once to power on the unit, Press again to power off.
when the unit is powered on, one of the input LEDs will illuminate depending on
your last selection of input source before power off.
The factory default setting for the input is CV (composite video).
The green LED illuminates when composite video is selected.
The Yellow LED illuminates when S-Video is selected.
2. Input select button:
Press the button to select your desired input source between composite
video and S- Video.
3. IR Sensor: Infrad remote control sensor.
4. Menu/Enter: This button serves two purposes.
a. Press the button to bring up OSD main control menu as shown in the "OSD Operation".
b. To act as a "enter" key to enter sub menu of you selected item or adjust
value of the selected item.
5/6. +/- button: Press the button to move up or down the tick "V" to your
desired parameter. Or after a parameter is selected by pressing MENU/ENTER button,
press the button to alter the value of your selected parameter.
Front Panel
(4). Operation Controls and Functions
2
Rear Panel
1. DC power jack: 5V 2A DC power input.
2. Composite Video: Use a Composite video cable to connect the composite video
output of the source equipment to this composite video(CV) input of the scaler.
3. S-Video: Use a S-Video cable to connect the S-Video output of the source
video equipment to this " S-Video" input on the back of the video scaler.
S-Video provides improved performance over composite video and is
recommended over composite.
4. DVI output: The CM-1391 can output a variety of PC and HDTV progressive
resolutions, in both digital and analog format through DVI-I connector.
Digital output: Connect CM-1391's digital DVI output to the DVI input of your
TV/display unit using a DVI to DVI cable .
Analog output: If you are to use CM-1391's analog output to connect to the
analog input of your PC or HDTV, you need to use a DVI to VGA adaptor to pull
out analog signal from the DVI-I connector . The DVI to VGA adaptor is then
connect to the VGA input of your display monitor through a VGA cable if
output is PC resolution, or connect to the YPbPr input of your HDTV through a
VGA to YPbPr/3 RCA adaptor cable if output is HDTV resolution.
Note: DVI to VGA adaptor is not included in the standard package,
and has to order separately.
(9). Specifications
Input Signal Levels
Video@1Vp-p, 75 ohm, Y@1 Vp-p, 75 ohm
Color@ 0.7 Vp-p, 75 ohm
Digital RGB
Output Connector
Output Singnal
Bit stream
Weight(g) 400
Output Signal Specifications
5
(8). Remote Control
1 3
4
2
1. Display: Press the button to display input source
and output resolution on the screen.
2. Power: Power ON/OFF button.
3. VGA~1080p: Press to select your desired
output resolution.
4. Picture: Press the button to enter picture
adjust submenu. Use +,- button to move
cursor (V) up/down to your desired
parameter, press "Picture" again to
confirm.
5. +/-: Press to move up/down the cursor (V)
to your desired parameter,or press to
increase/decrease the setting value.
6. Reset: Press to reset all setting back to
factory default value.
7. Exit: To exit OSD.
8. Video: Press the button to select
composite video input.
9. SVideo: Press the button to select
SVideo input.
6
55
8
7
9
5
4
3
2
1
DC 5V
SV CV
DVI-I OUTPUT INPUT
POWER INPUT MENU
CM-1391 Video to DVI Scaler Box
CV
SV
1 2 3 4 5 6
125(W) x 123(D) x 30(H)
0°C~40°C
Process Blue
Dimensions(mm)
Output Format
DVI-I Connector
Operating Temperature
Silkscreen Color
(7). DVI-I Pin Configuration
4
Output Setup
When Output Set up is selected a submenu as below appears:
Output Setup
Timing XGA
Exit
Press the " MENU/ENTER" button to enter into output timing select mode.
Press +,- to toggle through a variety of output resolutions as below.
Once your desired resolution is selected. press the menu/enter
to enter the resolution.
Note: 1. All output resolutions except 576p have 60Hz vertical rate,
The 576p resolution has 50Hz vertical rate.
1 8 C1 C2
C5
C4
C3
9
17 24
Combined Analog and Digital Connector Pin Assignments
Pin Signal Assignment Pin Signal Assignment
1
2
3
4
5
6
7
8
C1
C4
T.M.D.S Data2-
T.M.D.S. Data2+
T.M.D.S. Data2 Shield
N.C.
N.C.
DDC Clock
DDC Data
Analog Vertical Sync
Analog Red
Analog Horizontal Sync
9
10
11
12
13
14
15
16
C2
C5
T.M.D.S Data1-
T.M.D.S. Data1+
T.M.D.S. Data1 Shield
N.C.
N.C.
+5V Power
Ground
(Return for +5V, Hsync, and Vsync)
Hot Plug Detect
Analog Green
Analog Ground
(Analog R,G,&B return)
Pin Signal Assignment
17
18
19
20
21
22
23
24
C3
T.M.D.S Data0-
T.M.D.S. Data0+
T.M.D.S. Data0 Shield
N.C.
N.C.
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
Analog Blue
DVI-Integrated(DVI-I): Supports both analog and digital connections to the display.
This 29-pin connector can carry single or dual-link all-digital video/data signals
on 24 pins and uses 5 pins to carry analog video/data signals and ground.
VGA
SVGA
XGA
WXGA
SXGA
UXGA
WUXGA
480p
576p
720p
1080i
1080p
640x480
800x600
1024x768
1280x768
1280x1024
1600x1200
1920x1200
720x480
720x576
1280x720
1920x1080i
1920x1080p
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
50Hz
60Hz
Vertical rate Resolution
3
Use +,- button to move "V" to your desired parameter, then press MENU/ENTER
to enter into sub-menu of your selected parameter.
Picture Adjust
When Picture Adjust is selected a sub menu as below comes up.
Bright
Contrast
Color
Tint
Sharp
Default
Exit
USE +,- to move the tick (V) to your desired adjust item, Press the Menu/Enter
to confirm your selection.
At this point, the selected parameter will turn red, and you can use +,- to increase
or decrease the value of the parameter.
When adjustment is complete, Press "Menu" to leave the parameter. Move the tick "V"
to "Exit", then press menu/enter to exit.
(6). OSD Operation
After power on the unit , press the menu button to bring up the main menu
page as below:
Main Menu
Picture adj.
Output Setup
Exit
b. The format for analog PC output is RGB and for
analog HD output is YPbPr.
(5). Output Format
Default Range
16
16
16
16
05
OK
1-31
1-31
1-31
1-31
1-19
a. The format of digital DVI output is digital RGB
for all resolutions.
HDTV (RGBHV) HDTV (RGBHV)
-RGB
-RGB
-RGB
-RGB
-RGB
1080i-RGB
720p-RGB
576p-RGB
480p-RGB
1920x1080i
1280X720
720X576
720X480
UXGA
WUXGA -RGB
-RGB 1600 x 1200
1920 x 1200
1080p-RGB
1920x1080p follow input source
follow input source
follow input source
HDTV (YPbPr) HDTV (YPbPr)
-RGB
-RGB
-RGB
-RGB
-RGB
1080i-RGB
720p-RGB
576p-RGB
480p-RGB
1920x1080i
1280X720
720X576
720X480
UXGA
WUXGA -RGB
-RGB 1600 x 1200
1920 x 1200
1080p-RGB
1920x1080p follow input source
follow input source
follow input source
follow input source
follow input source
follow input source
VIDEO
VGA SVGA XGA
WXGA SXGA
480p
720p 1080i
PICTURE
RESET EXIT
-
+
576p
UXGA
1080p
WUXGA SVIDEO
CR-58
HDTV (RGBHV) HDTV (RGBHV)
-RGB
-RGB
-RGB
-RGB
-RGB
1080i-RGB
720p-RGB
576p-RGB
480p-RGB
1920x1080i
1280X720
720X576
720X480
UXGA
WUXGA -RGB
-RGB 1600 x 1200
1920 x 1200
1080p-RGB 1920x1080p follow input source
follow input source
follow input source