background image

6

Version 1.0

Building a serial DMX-chain:

Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture.

Always connect one output with the input of the next fixture until all fixtures are connected.

DMX-512 connection with DMX terminator:

For installations where the DMX cable has to run a long distance or is in an electrically noisy 

environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in 

preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an 

XLR plug with a 120 resistor connected between pins 2 and 3, which is then plugged into the output XLR 

socket of the last fixture in the chain.

Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 

resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the 

last fixture.

Power connection

Power Requirements

The FR-150W luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire contains 

an auto-ranging power supply.

Power linking between fixtures:

The fixture with powercon in and out socket. Connect the power out to the power in socket in the next 

fixture till all are connected.

Caution: maximum power linking - 8 units.

Connection with the mains:

Connect the device to the mains with the enclosed power supply cable.

The occupation of the connection cables as below:

Cable color

Connection

International

Brown 

Live

L

Blue 

Neutral

N

Yellow/green

Earth(Ground)

Operation

The FR-150W can operate in three different modes. In each mode you can run the fixture as a stand 

alone fixture or in a master/slave confiugration. This next section will detail the differences in the 

operating modes.

Control Menu Map

MENU

SUB MENU

OPERATION

Addr

001-512

RDM/DMX address

CHnL

1CH

Channel mode

2CH
3CH
4CH

Strb

S.01-s.20

Strobe with spead increasing

Summary of Contents for FR-150W












Reviews: