SETUP & ASSEMBLY INSTRUCTIONS
1.
Use 5mm alley key and separate upper and lower handlebar mounts
①②
2.
Wrap upper and lower handlebar mounts around the bicycle handlebars, directly either side of
the central handlebar mounting stem
3.
Insert x2 hex head allen key screws
⑫
through the upper mount
①
and lower mount
②
4.
Insert nylock nuts
⑨
into lower housing nut lock cavity and turn screws
⑫
to engage nuts
⑨
(do not fully tighten at this time)
5.
NOTE: Fangs have been designed for use on 31.6 mm standard size road bike handlebars, use
x2 spacers
⑤
inside upper & lower mounts
①
&
②
for handlebars that are smaller in size i.e.
25mm to 26mm in diameter, as found on some touring and trail bikes
6.
Insert reversable extension bracket
③
into the lower handlebar mount forward support boss
②
with the concave shape of the reversable extension bracket facing away from the centre of the
handlebars (curve towards the outside)
7.
Insert hex head allen key screw
⑧
through the lower handlebar mount forward support boss
and through the inner pivot arm spigot of the reversable extension bracket
③
8.
Install nylock nut
⑨
into lower housing nut lock cavity and turn screw
⑧
to engage nut
(do not fully tighten at this time)
9.
Insert phone mount pivot
④
over the outer spigot of the reversable extension bracket with the
twin gaps facing outwards
10.
(ensure the rounded side of the phone mount pivot
④
is facing up to accommodate the round
hex head allen key screw and the six-sided nut lock cavity is facing down)
11.
Install hex head allen key screw
⑪
trough the phone mount pivot
④
12.
Insert nylock nuts
⑨
into lower nut lock cavity and turn screws
⑪
to engage nuts
⑨
13.
Install x2 O-rings
⑦
over each of the inner and outer sides of vertical support arm
⑥
14.
(ensure the two O-rings
⑦
sit inside the spigot arm gap of the vertical arm
⑥
)
(Note: the O-rings will extend outwards from each side of the lower portion of the vertical
support arm lock (hook) out along the arm and onto the outer central recess of the arm)
15.
Install vertical support arm lower spigot into the twin gaps of the phone mount pivot
④
16.
Install Hex head Allen key screw (with one washer
⑩
under the head, through the phone mount
pivot bore engaging the lower spigot bore of the vertical support arm
17.
Install washer
⑩
under the nut
⑨
18.
Insert nylock nuts
⑨
into lower housing nut lock cavity and turn screws
⑫
to engage nuts
⑨
(do not fully tighten at this time)
19.
Position the upper and lower handlebar mounts
①
and
②
hard against the larger portion of
the handlebars directly either side of the handle bar stem.
20.
Set the angle of the Fangs so the upper and lower handlebar mounts are equal horizontal (or as
desired) and tighten both hex head allen key screws
⑫
until the upper and lower handlebar
mounts are firmly secured to the handlebars
21.
Tighten screws
⑧
and
⑪
so the reversable extension bracket
③
and phone mount pivot
④
are secured, but still moveable under firm pressure
22.
Hold nut
⑨
on the lower portion of the vertical support arm and tighten hex head allen key
screw
⑫
until the vertical support arm is secured but still moveable
23.
(do same for opposite arm)
Your Fangs are now ready for phone insertion
24.
Place phone or device into the lower locks of the vertical support arms, secure with x4 O-rings
25.
Adjust the pivot angles of the reversable extension bracket
③
and/or the Phone Mount Pivot
④
inwards, outwards or sideways to meet your specific Phone or device dimensions
(Note: the preferred mounting will be about a 15mm to 20mm from either side/end of your
smartphone)
26.
Set you Phone at your preferred angle of viewing by moving the Phone vertical support arms
⑥
up or down
27.
When slipping the O-rings up and over your phone take care to avoid the phone function
buttons on the side of your phone and your good to go
(Note: further information and FANG MOUNT set up can be found on Cyclevision Website)
Summary of Contents for FANG MOUNT CVFM-01-01
Page 1: ......
