CYBEX Eagle 11150 Owner'S And Service Manual Download Page 18

Page: 18 / 42

Cybex Eagle 11150 Incline Press Owner’s Manual

Assembly
Page 4-2

Rotate cam and disconnect weight stack belt from cam

(by loosening the two set screws on the belt clamp with
a 7/32” Allen wrench). See Figure 1.

Locate the pulley bracket that is located near the cam.

See Figure 2.

Remove bolt, washer and hex nut securing the pulley to

the pulley bracket.

Remove pulley from pulley bracket.

Remove one of the two BHSCS (Button Head Socket Cap Screws)

securing the pivot shaft. See Figure 3.

Carefully remove pivot shaft and pulley shaft. See Figure 3.

NOTE: Be extremely

careful when removing shaft so you don’t ruin the threads on the shaft.

With an assistant, carefully remove the six BHSCS

securing the two halves of the frame. See Figure 4.

Carefully move each half through the door-way to the

desired location.

With an assistant, carefully attach each half together

using the six BHSCS removed in step 4J. See Figure 4.

Carefully attach pulley shaft using the pivot shaft and

BHSCS removed in steps 4H and 4I. See Figure 3.

Reconnect pulley/cable to pulley bracket (removed in

steps 4F and 4G).

Verify both cables are routed properly.

Connect the weight stack belt to the belt clamp of

cam (removed in step 4D). See Figure 1.

Continue on with Step 5C.

5. Remove shipping feet and remove the back shrouds.

Carefully remove each (standard) cone-shaped

shipping support (using a 3/4” socket or wrench).

Cut shipping tie securing top weight.

Carefully place rubber feet (supplied with machine)

on each foot of the frame.

Lift top weight and turn the Increment Weight Adjusting

Knob to select all 15 lbs. (three increment weights each
side).

Remove the three Phillips head screws securing the

top (back) shroud and carefully remove the shroud.
See Figure 5.

Figure 2

Figure 3

Figure 4

Figure 5

Cam Bolt

BHSCS

Pivot Shaft

Washer

Pulley Shaft

Pulley/Cable

Nylon
Locknut

Washer

BHSCS (qty 4)

Nylon Locknut (4)

Nylon Locknut (2)

BHSCS (qty 2)

Phillips Head
Screw (3)

Figure 1

Cam

Set
Screws

Summary of Contents for Eagle 11150











































Search results

Summary of Contents for Eagle 11150

Reviews:

Related manuals for Eagle 11150

Brands by name

Popular brands

CYBEX Eagle 11150, Owner'S And Service Manual

Search results

Summary of Contents for Eagle 11150

Reviews:

Related manuals for Eagle 11150

Brands by name

Popular brands