background image

Page 7

Cybex Plate Loaded 16080 Chest Press Owner’s Manual

4 - Assembly

Tools Required

Rubber mallet

• 

Flat head screwdriver 

• 

NOTE:

   It is the responsibility of the facility owner/owner of the equipment to ensure that  

there is appropriate clearance around each machine to allow for safe use and passage.

NOTE:

  Refer to chapter 6 for reference diagrams.

1.   Read and understand all instructions thoroughly before starting any of the procedures  

listed on this instruction sheet. 

2.   Verify you have received the appropriate configuration.

Verify that you received the correct color machine that you ordered.

A. 

Verify you received the appropriate owner’s manual.  

B. 

Verify you received the warranty sheet.

C. 

3.  Move to desired location.

Note the diminsions of the machine: 

A. 

Machine Weight:

 

192 lbs. Size: 59” W x 50” L x 52” H 

Machine Weight 87 kg. Size: 150 cm W x 127 cm L x 132 cm H

Carefully remove shrink wrap securing rubber feet.

B. 

4.  Remove foot glides.

NOTE: 

Plastic shipping foot glides are used on Cybex Strength Systems machines to protect the bottom of machines  

 

     during transportation. These foot glides must be removed before a machine is first placed in service as the  

 

     shipping foot glides may cause the machine to be unstable.

WARNING: Failure to remove shipping foot glides before placing a machine in service may cause the machine  

 

          to be unstable, therefore, creating potential for personal injury or product damage.

NOTE: 

Failure to remove shipping foot glides before placing a machine in service may void warranty on the frames.

NOTE:

 

  

Be careful not to damage frame (such as chipping the paint) when removing foot glides.

NOTE:

 The foot of the machine will need to be raised slightly off the floor in order to remove foot glide. Do not install  

 

     weight stack (if applicable) until after removing foot glides.

1

. Using a rubber mallet, carefully strike foot glide.

2

. With a flat blade screwdriver, carefully pry off foot glide. 

3

. Carefully place rubber feet (supplied with machine) on each foot of the frame.

Summary of Contents for 16080

















Reviews: