background image

 12

Cybex Owner’s Manual

Clean Upholstery

If

Then

Light Soiling

1.  Prepare a solution of 10% household 

liquid soap and warm water. 

2.  Apply with a soft damp cloth. 

3.  If necessary, apply a solution of liquid 

cleanser with a soft bristle brush.

4.  Dampen a clean soft cloth in water and 

wipe residue away.

More Difficult Stains

1.  Prepare a solution of 10% household 

bleach (sodium hypochlorite) and 90% 

water. Dampen a soft white cloth in the 

solution.

2.  Rub gently on the stained area.

3.  Dampen a clean soft cloth in water and 

rinse area.

4.  If stains are still present, a full strength 

household bleach may be used. Allow 

bleach to puddle on the affected area 

or apply with a bleached-soaked cloth 

for approximately 30 minutes. Dampen 

a clean soft cloth in water, and rinse 

area to remove any remaining bleach 

concentration.

More Difficult Stains (Alternative Method)

1.  Dampen a soft white cloth with rubbing 

alcohol.

2.  Gently rub stained area.

3.  Dampen a clean soft cloth in water and 

rinse area.

Restoring Luster

1.  Apply a light coat of furniture wax for 30 

seconds.

2.  Lightly rub area using a clean white cloth.

Clean Frames

 Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry 

thoroughly. 

AVOID

 acid or chlorine based cleaners and also cleaners containing abrasives as these 

could scratch or damage the equipment.

Clean Chrome

Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral cleaners with a 

pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or chlorine based 

cleaners and also cleaners containing abrasives as these could scratch or damage the equipment.

Summary of Contents for 16062



















Reviews: