CyberPower PDU33 Series User Manual Download Page 88

Page: 88 / 96

3-Phase Intelligent PDU User Guide

Firmware Upgrade

3. Upload the cpsmpdumbfw_XXX.bin, type

- ftp > bin

- ftp > put cpsmpdumbfw_XXX.bin

4. Upgrade complete, type

- ftp > quit

5. The system will reboot after you type "quit". This reboot will take approx. 30 seconds.

6. Login to the PDU via FTP again, type

- C:\>ftp

- ftp> open 192.168.22.126 21 (for example: 192.168.22.126 is the current IP of

the PDU and 21 is the default ftp port for the PDU)

- Connected to 192.168.22.126.

- 220 CyberPower FTP Server Ready.

- User (192.168.22.126:(none)):cyber

- 331 User name okay, need password.

- Password:

- 230 User logged in, proceed.

- ftp>

7. Upload cpsmpdumbdata_XXX.bin, type

- ftp > bin

- ftp > put cpsmpdumbdata_XXX.bin

8. Upgrade complete, type

- ftp > quit

The system will reboot after you type “quit”.

Summary of Contents for PDU33 Series
































































































Search results

Summary of Contents for PDU33 Series

Reviews:

CyberPower PDU33 Series, User Manual, Page: 88 / 96

Search results

Summary of Contents for PDU33 Series

Reviews: