CyberPower PDU33 Series User Manual Download Page 41

Page: 41 / 96

Web Interface

3-Phase Intelligent PDU User Guide

Outlet Management

The following provides the outlet configurations to meet different application scenarios.

Remote Outlet On/Off/Reboot

Users can turn on, turn off, or reboot individual outlet. See

PDU Tab > Outlet Action > Control

(For

Switched Metered by Outlet Series and Switched Series only.)

PDU Tab > Outlet Action > Control

Item

Definition

HOST/GUEST#

Select the role of PDU (HOST or GUEST#) if PDUs are daisy

chained. Up to 3 GUEST PDUs can connect to 1 HOST PDU.

Control Action

Turn On

Selected outlets will be immediately turned on.

Turn On + Delay

elected outlets will be turned on according to each outlet’s

Power

On Delay

PDU Tab > Manager > Outlet

Turn Off

Selected outlets will be immediately turned off.

Turn Off + Delay

elected outlets will be turned off according to each outlet’s

Power

Off Delay

PDU Tab > Manager > Outlet

This action could signal a computer to shut down, if PowerPanel®

Business Edition Client software is installed on it.

Summary of Contents for PDU33 Series
































































































Search results

Summary of Contents for PDU33 Series

Reviews:

CyberPower PDU33 Series, User Manual, Page: 41 / 96

Search results

Summary of Contents for PDU33 Series

Reviews: