CyberPower OP1250 User Manual Download Page 18

 

 

 

 

 

FCC Notice 

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant 
to Part 15 of the FCC Rules.    These limits are designed to provide reasonable protection against 
harmful interference in residential installation.    This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications.    However, there is no guarantee that interference will not occur in 
a particular installation.    If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:    (1) Reorient or relocate the receiving 
antenna.    (2) Increase the separation between the equipment and receiver.    (3) Connect the equipment 
into an outlet on a circuit different from that to which the receiver is connected.      (4) Consult the dealer 
or an experienced radio/TV technician for help.      Any special accessories needed for compliance must 
be specified in the instruction.     
 

CAUTION:

    A shielded-type power cord is required in order to meet FCC emission limits and also to 

prevent interference to the nearby radio and television reception.    It is essential that only the supplied 
power cord be used.    Use only shielded cables to connect I/O devices to this equipment.   
 

CAUTION:

    Any changes or modifications not expressly approved by the guarantee of this device could 

void the user’s authority to operate the equipment. 

 

 

 

 

 

For more information, contact us at: 

CyberPower Systems (USA), Inc. 

5555 12

th

 Avenue East, Suite 110 

Shakopee, MN55379 

Tel:  (952) 403-9500 

Fax:  (952) 403-9500 

Email:  

[email protected]

 

Web:  

www.cyberpowersystems.com

 

 

 

Entire contents copyright ©2003 CyberPower Systems, Inc. 

All rights reserved. Reproduction in whole or in part without permission is prohibited. 

PowerPanel™ and PowerPanel Plus™ are trademarks of CyberPower Systems (USA), Inc.

 

 

 

Summary of Contents for OP1250



















Reviews: