manualshive.com logo in svg

Cyber Suite CYB-KLED, Installation Manual, Page: 23 / 32

Share
Download
Cyber Suite CYB-KLED Installation Manual Download Page 23

 

20 

CYB-KLED CyberSuite Installation Manual 

Reporting Options ([MENU] , [2] , [3]) 

 

The reporting options are a set of functions that relate to the 
reporting of information to the on site monitoring application or 
offsite central station. The system can further be configured for each 
reportable event to go to monitoring station and the local on site 
monitoring.  
 
To enter the Reporting Options Menu, press 
 

[MENU] , [2] , [3] 

 
To toggle options press the keys [1] to [8] , and the corresponding 
Zone LED will be lit when that option is ENABLED.  
 
Pressing the [ENTER] key will save the options.  

 
Option 1 - Report Arming and Disarming 
 

5

 

Enabled the CyberSuite keypad will send a message to 
the system controller when the system is armed or 
disarmed. If this option is disabled the current status 
of the CyberSuite keypad will not be valid. It is 
recommended this and the Report Alarm options are 
always enabled. 
 

6

 

Disabled no message will be sent. 

 

Option 2 - Report Alarms (Fire and Normal) 
 

5

 

Enabled the CyberSuite keypad will send a message 
when an alarm occurs on the CyberSuite system. This 
also enables the sending of the alarm silenced and 
alarm timed out messages. 
 

6

 

Disabled no message will be sent for an alarm event. 

 

Option 3 - Report Zone Bypass 
 

5

 

Enabled the system will report when the CyberSuite 
system is armed with zones that have been bypassed. 
 

6

 

Disabled no message will be sent when the user arms 
the system with zone(s) bypassed. 

 

Summary of Contents for CYB-KLED

































Reviews:

No comments